Electronics Forum | Fri Apr 13 12:37:35 EDT 2001 | edylc
>>> gold finger was covered by a Kapton tape and it was done offline away from the Screen printer or rather from the SMT lines itself, we are using an ENIG Pcb's , the process doesnt need a wave soldering ....however at the final end of the line ,
Electronics Forum | Tue May 13 06:57:10 EDT 2003 | davef
Your vendor site is totally correct. 2Ag is an excellent solder, but it does nothing to prevent tin and gold from reacting chemically. An earlier poster is correct gold goes into solution in liquid solder very fast, less than a second. Gold and ti
Industry News | 2010-09-13 15:36:15.0
IPC — Association Connecting Electronics Industries® has released IPC-1601, Printed Board Handling and Storage Guidelines. The industry's sole standard on the handling, packaging and storage of printed boards, IPC-1601 provides users with guidance on how to protect printed boards from contamination, physical damage, solderability degradation, electrostatic discharge and moisture uptake.
Industry News | 2011-01-18 13:46:21.0
Time and again, a major challenge lies in attaching integrated circuits (ICs) to highly integrated circuit board substrates in a space-saving manner. Würth Elektronik took this challenge on and found an ideal solution with the ESC (encapsulated solder connection) process. The chips are soldered and at the same time glued 'face-down" in their exact position.
Technical Library | 2013-01-17 15:37:21.0
A problem exists with electroless nickel / immersion gold (ENIG) surface finish on some pads, on some boards, that causes the solder joint to separate from the nickel surface, causing an open. The solder has wet and dissolved the gold. A weak tin to nickel intermetallic bond initially occurs, but the intermetallic bond cracks and separates when put under stress. Since the electroless nickel / immersion gold finish performs satisfactory in most applications, there had to be some area within the current chemistry process window that was satisfactory. The problem has been described as a 'BGA Black Pad Problem' or by HP as an 'Interfacial Fracture of BGA Packages…'[1]. A 24 variable experiment using three different chemistries was conducted during the ITRI (Interconnect Technology Research Institute) ENIG Project, Round 1, to investigate what process parameters of the chemical matrix were potentially satisfactory to use and which process parameters of the chemical matrix need to be avoided. The ITRI ENIG Project has completed Round 1 of testing and is now in the process of Round 2 TV (Test Vehicle) build.
Technical Library | 2021-10-20 18:21:06.0
The solderability of the SAC305 alloy in contact with printed circuit boards (PCB) having different surface finishes was examined using the wetting balance method. The study was performed at a temperature of 260 _C on three types of PCBs covered with (1) hot air solder leveling (HASL LF), (2) electroless nickel immersion gold (ENIG), and (3) organic surface protectant (OSP), organic finish, all on Cu substrates and two types of fluxes (EF2202 and RF800). The results showed that the PCB substrate surface finish has a strong effect on the value of both the wetting time t0 and the contact angle h. The shortest wetting time was noted for the OSP finish (t0 = 0.6 s with EF2202 flux and t0 = 0.98 s with RF800 flux), while the ENIG finish showed the longest wetting time (t0 = 1.36 s with EF2202 flux and t0 = 1.55 s with RF800 flux). The h values calculated from the wetting balance tests were as follows: the lowest h of 45_ was formed on HASL LF (EF2202 flux), the highest h of 63_ was noted on the OSP finish, while on the ENIG finish, it was 58_ (EF2202 flux). After the solderability tests, the interface characterization of cross-sectional samples was performed by means of scanning electron microscopy coupled with energy dispersive spectroscopy.
SMTnet Express, November 19, 2020, Subscribers: 27,983, Companies: 11,189, Users: 26,264 Every month ... • Of the 88,000 engineers who visit SMTnet, over 87% came from Search engines • So, over 76,000 engineers found your content
SMTnet Express, July 12, 2018, Subscribers: 31,180, Companies: 10,985, Users: 24,934 Improving Thermal Cycle and Mechanical Drop Impact Resistance of a Lead-free Tin-Silver-Bismuth-Indium Solder Alloy with Minor Doping of Copper Additive T. Wada
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2022/04/Vacuum-Void-Reduction-Reflow-1.pdf
]. Thus even with vacuum reflow, the debate remains regarding the effect of voiding on solder joint reliability. This paper reports the results from a test To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
| https://www.smtfactory.com/I-C-T-High-Speed-on-Line-3D-SPI-Solder-Paste-Inspection-Equipment-I-C-T-S400-pd49143724.html
I.C.T High Speed on-Line 3D SPI Solder Paste Inspection Equipment I.C.T-S400 from China manufacturer - Dongguan Intercontinental Technology Co.,Ltd. English Français Pусский Español Português Deutsch Italiano 日本語 한국어 Tiếng Việt
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
