Industry Directory | Manufacturer
Nepes offers flip chip solutions ranging from wafer bumping to advanced packaging and testing for IC manufactures, module electronics and end-product makers.
New Equipment | Rework & Repair Equipment
The BEST Gold Contact Replating Kit includes the tools you need for fast replating and modification of circuit contacts. Edge contacts may require replating if they are contaminated with solder or become scratched during handling or do not meet the m
New Equipment | Cleaning Agents
AQUANOX® A4708 is a neutral range pH chemistry designed to rapidly clean under densely populated low-gap PWB assemblies. AQUANOX® A4708 is effective on all flux types including no-clean and water soluble residues. AQUANOX® A4708 is specifically form
Electronics Forum | Wed Jul 17 02:32:13 EDT 2002 | computer
Hi, Anybody with a solution on solder balls on gold pad. I have tried the following a) Check cleanliness of solder paste printing area b) Clean stencils on 1 clean per 2 prints c) Use N2 on the reflow oven. Any other methods...
Electronics Forum | Wed Jul 17 08:26:14 EDT 2002 | davef
Search the fine SMTnet Archives to get started.
Industry News | 2018-10-18 10:16:53.0
Solder Tinned Pads vs Gold Plated Pads - The Importance of Selecting the Proper Surface Finish
Industry News | 2010-12-03 21:35:04.0
Eastern Europe's growing electronics assembly industry faces new challenges, especially with the adoption of lead-free technology. To connect manufacturers with solutions to these challenges, IPC — Association Connecting Electronics Industries® is holding the IPC Conference on Quality, Reliability and Acceptability for Electronics Manufacturing in Budapest, Hungary, on 22–24 February 2011.
Parts & Supplies | Circuit Board Assembly Products
1). 100mm x 98mm/1up, FR-4, 2). 1mm +/-0.1mm，6 Layers 3). 1oz copper finished 3). Green solder mask/white legend 4). Min. hole 0.15mm, 4/4 mil track/gap 5). Blind via layer 1-2, via-in-pad. 6). Immersion gold surface finish
Parts & Supplies | Circuit Board Assembly Products
PULANG TECHNOLOGY CO,.LTDOffers electronic manufacturing services including PCB designing, electronic contract manufacturing including electronic product design, electronic product development, electronic product repair, PCB manufacturing, electronic
Technical Library | 2023-09-07 14:38:31.0
A repeat customer specializing in high-technology interconnect, sensor, and antenna solutions, partnered with us to dispense small volumes of solder paste (Indium 10.1 SAC305 T6SG 78%m) onto backplane connectors – gold pads 0.175mm x 0.225mm. We performed a test requiring 0.200mm diameter or smaller dots to demonstrate the dispensing capability required.
Technical Library | 2023-08-04 15:27:30.0
A designed experiment evaluated the influence of several variables on appearance and strength of Pb-free solder joints. Components, with leads finished with nickel-palladium-gold (NiPdAu), were used from Texas Instruments (TI) and two other integrated circuit suppliers. Pb-free solder paste used was tin-silver-copper (SnAgCu) alloy. Variables were printed wiring board (PWB) pad size/stencil aperture (the pad finish was consistent; electrolysis Ni/immersion Au), reflow atmosphere, reflow temperature, Pd thickness in the NiPdAu finish, and thermal aging. Height of solder wetting to component lead sides was measured for both ceramic plate and PWB soldering. A third response was solder joint strength; a "lead pull" test determined the maximum force needed to pull the component lead from the PWB. This paper presents a statistical analysis of the designed experiment. Reflow atmosphere and pad size/stencil aperture have the greatest contribution to the height of lead side wetting. Reflow temperature, palladium thickness, and preconditioning had very little impact on side-wetting height. For lead pull, variance in the data was relatively small and the factors tested had little impact.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
This video presents the capabilities of BEST Inc in terms of its ability to perform high end PCB rework and repair services. BEST Inc., located in Rolling Meadows IL is a company of soldering "geeks". We rework/repair PCBs, train and certify solderin
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Tue Jan 23 00:00:00 EST 2018 - Tue Jan 23 00:00:00 EST 2018 | New Milford, Connecticut USA
FREE Webinar: Eliminate Circuit Board Problems and Failure Modes
SMTnet Express, September 7, 2017, Subscribers: 30,782, Members: Companies: 10,712, Users: 23,761 Challenges on ENEPIG Finished PCBs: Gold Ball Bonding and Pad Metal Lift Young K. Song and Vanja Bukva; Teledyne DALSA As a surface finish for PCBs
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/Vacuum-Void-Reduction-Reflow.pdf
Vacuum Reflow Processing On Solder Joint Voiding To be published in the Proceedings of SMTA International, September 17 - 21, 2016, Rosemont, IL
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/solder-mask-on-0-40-pitch-qfn_topic3127.html
Solder Mask On 0.40 Pitch QFN - PCB Libraries Forum Forum Home > Libraries > Footprints / Land Patterns New Posts FAQ Search Events Register Login Solder Mask On
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411
