New Equipment | Solder Materials
Indium Corporation manufactures high quality solder powders and pastes. Powders are available in hundreds of alloys and a full range of sizes. Solder pastes can be made from these powders using a wide variety of flux vehicles to get the best fit for
New Equipment | Solder Materials
NC275B Liquid Flux is a water-based VOC-Free flux that has performance and reliability characteristics equal or superior to many alcohol-based fluxes. A medium-solids/residue flux, NC275B can be used with all common lead-free wave soldering alloys in
Electronics Forum | Fri Jul 15 16:53:56 EDT 2005 | davef
Questions are: * Are you sure there was solder on the pad prior to placing the component? * Is there solder on the lead, but not on the pad?
Electronics Forum | Mon Jul 18 09:35:42 EDT 2005 | stepheniii
If it were other machines I would suggest the possibility of air kiss blowing the solder away, but mydata's have a release to make sure the air kiss never gets too high. Unless it is not pointing 90 degrees away from the machine like mydata recommend
Used SMT Equipment | Soldering - Selective
Juki Cube 460 Selective Solder system Don't miss out on this opportunity to own this Excellent Selective Soldering Machine the Juki CUBE-460 Year 2022 ! The Juki Cube 460 is the most accessible selective solder that allows for easy setup & easy maint
Industry News | 2018-10-18 08:00:40.0
SMT solder joint quality and appearance inspection process
Industry News | 2018-10-18 08:01:00.0
SMT solder joint quality and appearance inspection process
Technical Library | 2007-08-16 13:34:31.0
While experienced inspectors may be able to determine the aesthetic differences between a lead-free PCB assembly and a tin-lead version, one cannot rely on the "experienced eye". "Less wetting out to the pad edges" (Figure A) and "graininess and lack of shininess of the solder joint" (Figure B) are typical comments about some lead-free solder joints. However, in cases where a Nitrogen atmosphere was present during the reflow of the solder joint (Figure C), there will be little visual differences between the lead free alloys and their tin-lead counterparts.
Technical Library | 2014-03-06 19:04:07.0
Over the last few years, there has been an increase in the rate of Head-in-Pillow component soldering defects which interrupts the merger of the BGA/CSP component solder spheres with the molten solder paste during reflow. The issue has occurred across a broad segment of industries including consumer, telecom and military. There are many reasons for this issue such as warpage issues of the component or board, ball co-planarity issues for BGA/CSP components and non-wetting of the component based on contamination or excessive oxidation of the component coating. The issue has been found to occur not only on lead-free soldered assemblies where the increased soldering temperatures may give rise to increase component/board warpage but also on tin-lead soldered assemblies.
https://www.ascen.ltd/Products/Solder_paste_printer/513.html full auto PCB screen printer and SMT solder paste printing machine with Image and optical system,It is a very accurate fully automatic SMT stencil printer.automatic PCB screen printer main
https://www.ascen.ltd/Products/Solder_paste_printer/513.html full auto PCB screen printer and SMT solder paste printing machine with Image and optical system,It is a very accurate fully automatic SMT stencil printer.automatic PCB screen printer main
Training Courses | | | PCB Assembly Courses
The PCB assembly courses provide knowledge of different processes and equipment used in TH and SMT assembly of printed circuit boards.
Events Calendar | Wed Mar 07 00:00:00 EST 2018 - Wed Mar 07 00:00:00 EST 2018 | ,
Solder Paste Qualification Testing - SMTA Webinar
Events Calendar | Thu Oct 03 00:00:00 EDT 2019 - Thu Oct 03 00:00:00 EDT 2019 | ,
IPC Tech Ed Webinar Series: Ball Grid Array (BGA) and Bottom Termination Component (BTC) Design and Assembly Challenges: Reflow Profiling to Achieve Low Defect Rates and Successful Assembly! – Part 2
Career Center | , Maryland USA | Engineering
Late stage start-up company, well into commercialization, that develops and manufactures products to precisely control the instantaneous release of heat energy for reaction initiation and joining applications. Building from its strengths in material
Career Center | Baguio City, Philippines Philippines | Engineering
Responsible to effectively utilize all of the available resources such as machines, materials, manpower and methods in order meet the Offsite metric goal according to the customers’ specifications, requirements and needs; Responsible for evalua
Career Center | Wesley Chapel, Florida USA | Engineering,Management,Quality Control
15 years of experience on Electronic Manufacturing. Certified SMT Process Engineer TQM Knowledge Statistics DOE Screen Printer Thermal Process Knowledge JIT International Project Engineering Experience
SMT Express, Issue No. 3 - from SMTnet.com Volume 1, Issue No. 3 Wednesday, August 18, 1999 Featured Article Return to Previous Page BGA REWORK Earl Moon Proof Of Design (POD) PART INSPECTION BEFORE OPERATIONS Always inspect part
SMT Express, Issue No. 5 - from SMTnet.com Volume 1, Issue No. 5 Wednesday, October 13, 1999 Featured Article Return to Front Page HASL WHAT A HASSLE, or HASL'd AGAINby Earl Moon INTRODUCTION This article updates one I wrote for Printed
| http://etasmt.com/cc?ID=te_news_industry,24361&url=_print
SMT Reflow Oven Reflow soldering process-SMT Technical-Reflow oven,SMT Reflow Soldering Oven-cmsadmin Reflow oven,SMT Reflow Soldering Oven 当前位置: Home >> News
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/leadfree.pdf
– no wetting to entire pad PROPRIETARY AND CONFIDENTIAL INFORMATION Pages: 24 of 24 Rev Level: 1 Rev Date: 1/03/01 Conclusion • No lead solders provide a robust process, excellent results at all soldering conditions considered • Potential concern – Voids
