Industry Directory | Consultant / Service Provider / Distributor / Manufacturer
ORION provides innovative solutions to our customers' EMI/RFI Shielding, Insulating, Screening and Sealing needs in a broad spectrum of manufacturing environments.
Industry Directory | Manufacturer
Thermally Managed ( up to 1000 W /m K thermal transfer rate ), CTE controlled, Very Rigid, Light Weight STABLCOR PCB / Substrate Technology
We are well versed in the following thermal application materials: Sil-Pad thermally conductive insulators Gap-Pad thermally conductive gap filling material Q-Pad thermal grease replacement film Bond-Ply thermally conductive adh
Waterjet allows for improved cutting tolerances, improved lead times and the ability to provide highly complex geometry. Using a stream of water with forces of 55,000 PSI yields fast production rates and tool free cutting. Our single head and 4-head
Electronics Forum | Tue Dec 28 03:59:06 EST 2010 | riscy00
I'm investigating heat transfer by 1st order approximation between PCB and ambient air via encapsulate material (epoxy or gel or silicone), they have thermal conductivity of 0.2W/C but it hard to find specific heat capacity and density. Has anyone
Electronics Forum | Mon Dec 09 08:13:06 EST 2002 | MA/NY DDave
Hi Yes it is common to design for more uniform heat transfer during the soldering phase or even during the operation phase. It all depends on how bad the problem is during automated assembly or during usage. The only difficulty is that the designer
Used SMT Equipment | Chipshooters / Chip Mounters
Product name: YV100 yamaha economical chipmounter Product number: YV100 Products in detail YAMAHA multi-function chip mounter YAMAHAYV100A Substrate size: ATS20 (end to put) W - ATassembly: L460 * W250 (Max)/L50 * W50 (Min) Substrate thickness: 0.4
Used SMT Equipment | SMT Equipment
Product name: YV100 yamaha economical chip mounter Product number: YV100 Products in detail YAMAHA multi-function chip mounter YAMAHA YV100A Substrate size: ATS20 (end to put) W - AT assembly: L460 * W250 (Max)/L50 * W50 (Min) Substrate thick
Industry News | 2003-02-24 09:32:24.0
Now available with an easy-to-use dispensing gun, Electrolube TCR is a single-component, highly thermally conductive RTV sealant.
Industry News | 2003-03-11 08:45:00.0
CAMtastic DXP is the latest version of Altium's complete CAM verification and editing system that bridges the gap between PCB design and manufacturing and facilitates communication between board designers, fabrication engineers, and their clients.
Parts & Supplies | Assembly Accessories
Detailed Product Description Features: 7 Channel Brand: KIC Part Name: X5 Reflow Profiler Model: X5 Condition: Original New Leadtime: 7days KIC X5 Thermal Profiler with SPC software and RF capability For Reflow Track More Data Points With 7,
Parts & Supplies | Chipshooters / Chip Mounters
> JUKI ESL13000000 VACUUM PAD 15 JUKI ESL13000100 PHOTO MICRO SENSOR A JUKI ESL13001000 TUBE union (KL700) JUKI ESL130011A0 CONVEYOR MOTOR (KZ500) JUKI ESL13002000 CLAMP LEVER JUKI ESL13003000 T TYPE NUT JUKI ESL130031A0 OPERATION PANEL (KL700) JUKI
Technical Library | 2024-08-20 00:41:48.0
Thermal interface materials (TIMs) play a pivotal role in ensuring efficient thermal management by facilitating heat transfer between heat generating components and heat-dissipating devices
Technical Library | 2019-11-12 02:09:22.0
Thermal shock test chamber can be used for testing the chemical change or physical damage on composite materials caused by the thermal expansion and contraction of the sample in the shortest time,which is subjected to extremely and continuous high and low temperature environment.so how to check the temperature recovery time of this chamber? Normally we take following steps to inspect the temepratuire recovering time: 1.Install the temperature sensor at the specified position, and adjust the temperature controller of hot zone and cold zone to the required nominal temperature respectively. 2.The temperature increases and reduces respectively,30min after temperature in two zones reach stable status,record temperature value of the measuring point,pls set the temperature value of two zones to be required nominal temperature. 3.The temperature shock test chamber automatically places the inspected load into theh ot zone,select the corresponding retention time according to regulated standard. 4.Set the transfer time,then the inspection load is transferred from hot zone to cold zone, and the temperature of the measuring point is observed and recorded, and then the reverse conversion of the load from cold zone to hot zone is carried out according to the same method, and the temperature of the measuring point is observed and recorded. www.climatechambers.com
The Centurion™ is a forced-convection SMT reflow system with tight, closed-loop process control, built for today’s high-throughput PCB assembly environments. With the best heat transfer in the industry, the Centurion is able to run any profile at the
Events Calendar | Wed Mar 18 00:00:00 EDT 2020 - Wed Mar 18 00:00:00 EDT 2020 | College Park, Maryland USA
CALCE Reliability Science Symposium - Spring 2020
Career Center | Rochester, New York USA | Engineering
Our high tech client located in the Western NY State area offers you the following challenge. Complete mechanical design responsibility from specification to the manufacturing process. We seek a candidate that has the following experience: Design
Career Center | Stoneham, Massachusetts | Engineering,Production,Research and Development,Technical Support
Warren P. Pumyea 8 Beacon Street Stoneham, Massachusetts 02180 Cell #: 978-821-7335 * E-mail: warren@pumyea.com http://www.pumyea.com/Process_Manufacturing_Engineer.doc Objective: Seeking a position as an engineer or related discipline whic
Career Center | Nariveles, Philippines | 2019-11-21 13:32:04.0
Failure Analysis Technician Quality-driven and goal-focused with strong research, planning and Problem-solving abilities. Gifted in being a technical knowledge base, Organizing workflow and improving processes.
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/efd/products/thermal-compounds/thermal-compound
) Our innovative, non-silicone thermal compounds provide an ideal thermal solution by ensuring reliable heat transfer over a longer time than most industrial thermal interface materials
1st Place Machinery Inc. | http://www.firstplacemachinery.com/firstplace_plastics_chillers_thermalcare2.html
Thermal Care Chiller 2 Thermal Care 10 Ton Water Cooled Chiller Model # AQOR1104 SERIAL # 97860019803 10 Tons VOLTAGE 460-3-60 FULL LOAD AMPS
