If you have boards requiring high tolerance mechanical dimension or odd shapes that traditional depaneling methods cannot handle. BEST Inc. provides laser depaneling services for printed circuit board manufacturers as well as EMS and OEMs. BEST’s nu
New Equipment | Rework & Repair Equipment
BEST HeatShield Gel™ is a thermal shield water-based gel designed to be used in the PCB rework/repair or board assembly areas in order to provide thermal protection of electronic components. It is truly a revolutionary means to protect components. It
Electronics Forum | Tue Dec 30 20:48:31 EST 1997 | Tom Gervascio
Has anyone had any experience with thermal shocking and cracking of SMD capacitors during the rework process? My company was advised to preheat capacitors to 125 C at a rate of 2 C/sec before replacing them onto boards. Would this maybe degrade c
Electronics Forum | Thu Feb 11 08:14:41 EST 2010 | scottp
It's OK to have the daisychain done in the interposer rather than the die (and a lot cheaper) but in thermal cycling the parts MUST have representative die. That's where a large part of the CTE mismatch comes from to cause fatigue damage. Thermal c
.jpg)
Used SMT Equipment | Soldering - Reflow
Features 1. Full hot air reflow heat fast, high thermal efficiency compensation, delta t less than ± 2 ℃ soldering is uniform. 2. HELLER company has 40 years of history, process maturity. 3. maintenance costs low, the furnace normal use, electrici
Industry News | 2018-04-22 19:12:45.0
SMTA Europe announces Session 7 Technical Program on High Temperature PCB Materials and Fabrication at the “Electronics in Harsh Environments Conference” to be held in Amsterdam, Netherlands, on April 25th, 2018.
Industry News | 2010-04-30 18:47:15.0
SMTA China announces that it presented awards for the 10 best papers/presentations and two best exhibits at the SMTA China East 2010 Conference Award Presentation Ceremony, held on Wednesday, April 21, 2010 at the Shanghai Everbright International Hotel in conjunction with the SMTA China Annual Breakfast Reception.
Technical Library | 2022-12-05 16:28:06.0
The work evaluates the impact of latent heat (LH) absorbed or released by a solder alloy during melting or solidification, respectively, on changes of dimensions of materials surrounding of the solder alloy. Our sample comprises a small printed circuit board (PCB) with a blind via filled with lead-free alloy SAC305. Differential scanning calorimetry (DSC) was employed to obtain the amount of LH per mass and a thermomechanical analyzer was used to measure the thermally induced deformation. A plateau during melting and a peak during solidification were detected during the course of dimension change. The peak height reached 1.6 μm in the place of the heat source and 0.3 μm in the distance of 3 mm from the source. The data measured during solidification was compared to a numerical model based on the finite element method. An excellent quantitative agreement was observed which confirms that the transient expansion of PCB during cooling can be explained by the release of LH from the solder alloy during solidification. Our results have important implications for the design of PCB assemblies where the contribution of recalescence to thermal stress can lead to solder joint failure.
Technical Library | 2009-04-30 18:06:24.0
This presentation surveys the most significant via and via-related laminate failure mechanisms from past to present using data from current induced thermal cycling (CITC) testing, failure analysis, and other sources. The relative life and failure modes of thru vias, buried vias, and microvias (stacked vs. non-stacked) are compared, along with the affect of structure, materials, and peak temperatures on the above. The origin of via-induced laminate failures such as "eyebrow cracks" and Pb free related internal delamination is also explored.
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Career Center | , District of Columbia | Engineering,Management,Production,Sales/Marketing
• Strong technical leadership and decision-making skills; strong verbal and written communication skills to provide clear, crisp direction for key issue resolution; and good team skills to facilitate cross-functional cross -site team effectiveness.
SMTnet Express, December 23, 2015, Subscribers: 23,927, Members: Companies: 14,845, Users: 39,621 PCB Fabrication Processes and Their Effects on Fine Copper Barrel Cracks Edward Arthur, Charles Busa, Melissa Durfee, Chad Gibson, Wade Goldman P
Imagineering, Inc. | https://www.pcbnet.com/blog/everything-you-need-to-know-about-moisture-sensitive-devices-msds/
. These standards classify moisture sensitivity levels, or MSLs, on a scale from 1 to 6 depending on their susceptibility to moisture-induced damage
40731 | https://www.smta.org/harsh/2018-Harsh-Environments-Program.pdf
Surface Mount Technology Association (SMTA)
