A quality pcb assembly contractor, small to large orders filled at reasonable prices , thru hole soldering and rework , or pcb modifications and repairs. loading and inspection.
Supply chain management expert, Zurvahn is an Electronic Manufacturing Service provider for mid- to low-volume products to Original Equipment Manufacturers worldwide.
Outsource your PCB assembly with us and let us show we can be you manufacturing partner on Mexico. Our quality services and low cost will make you profits increase and your problems desapear. We have both, SMT and thru hole capabilities, as well as
New Equipment | Board Handling - Pallets,Carriers,Fixtures
Selective solder fixtures protect bottom side SMT components & eliminate the risk of loosing parts in the solder. Our unique designs will eliminate skipping and bridging. No need to tape areas which reduces operator time and speeds up your line.
Electronics Forum | Wed Dec 17 09:53:26 EST 2003 | davef
IPC-2222 - Sectional Design Standard For Printed Board For Organic Printed Boards, Table 9-3 � Plated Through Hole Diameter To Lead Diameter Relationships will give you the standard information you require. If we can�t get proper hole fill after try
Electronics Forum | Wed May 27 10:19:43 EDT 1998 | Jerry
We have no problems but orientation does matter. Orient with longest side of component body perpendicuar to wave. In other words the same preference as with through hole DIPS. Idea is the same as for through hole, that the surface tension will ten
Industry News | 2010-12-07 14:53:07.0
GPD Global announces that its Positive Cavity Displacement (PCD) technology is proven with silver-filled electrically and thermally conductive adhesives.
Industry News | 2012-02-15 19:18:44.0
GPD Global announces that its PCD4H Dispense Pump yields excellent results with phosphor and non-phosphor-filled LED encapsulation as viewed on the color chart by tightly grouped results.
Technical Library | 2023-11-14 19:52:11.0
The continuous drive in the Electronics industry to build new and innovative products has caused competitive design companies to develop assemblies with consolidated PCB designs, decreased physical sizes, and increased performance characteristics. As a result of these new designs, manufacturers of electronics are forced to contend with many challenges. One of the most significant challenges being the processing of thru-hole components on high thermal mass PCBs having the potential to exceed 20 layers in thicknesses and have copper mass contents of over 40oz. High thermal mass PCBs, coupled with the use of mixed technologies, decreased component spacing, and the change from Tin Lead Solder to Lead Free Alloys has lead many manufacturing facilities to purchase advanced soldering equipment to process challenging assemblies with a high degree of repeatability.
Technical Library | 2020-07-15 18:29:34.0
In the early 2000s the first fine-pitch ball grid array devices became popular with designers looking to pack as much horsepower into as small a space as possible. "Smaller is better" became the rule and with that the mechanical drilling world became severely impacted by available drill bit sizes, aspect ratios, and plating methodologies. First of all, the diameter of the drill needed to be in the 0.006" or smaller range due to the reduction of pad size and spacing pitch. Secondly, the aspect ratio (depth to diameter) became limited by drill flute length, positional accuracy, rigidity of the tools (to prevent breakage), and the throwing power of acid copper plating systems. And lastly, the plating needed to close up the hole as much as possible, which led to problems with voiding, incomplete fill, and gas/solution entrapment.
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
With the development of miniaturization of assembly components, the layout area and pattern design area of PCBs have also been continuously reduced, and PCB manufacturers are constantly updating the production process to conform to the development tr
Career Center | Dallas, Texas USA | Engineering
Skills/Requirements: BS in Engineering, 5+ years in SMT and thru hole, mfg. engineering, NPI, DFM, good documentation and organizational skills, high volume, advanced manufacturing, problem solving skills. Duties/Functions: Provide support for new pr
Career Center | South Windsor, Connecticut USA | Engineering,Technical Support
Posting JK-NVPE Process Engineer(PCB Assembly and support)- Our client, located in northern Connecticut, seeks a process engineer capable of providing engineering support in the development and/or improvement of current or new technologies and proces
Career Center | , | Engineering,Production,Quality Control
SMT EXPERT WITH DOE ,DFM AND LEAN SKILLS
Career Center | Gurgaon, Haryana India | Management
� Heading daily morning meeting with all program managers, materials manager, test engineering manager, process engineering manager, quality control manager, planning manager, stock room manager, shipping department head. Discussion about incoming or
SMTnet Express, March 3, 2016, Subscribers: 24,124, Companies: 15,000, Users: 40,059 Nanocopper Based Paste for Solid Copper Via Fill David Ciufo, Sujatha Ramanujan, Janet Heyen, Michael Carmody; Intrinsiq Materials , Sunny Patel; Candor
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/how-to-specify-plated-holes_topic1400_post5615.html
. I spotted that problem right away. Unfotunately, round two has this thru-hole plating problem. I need to figure this out before round three
Imagineering, Inc. | https://www.pcbnet.com/quote/board-quote-usa/?cpn=3
* Thru Hole Placements BGA / QFN AS9100 Double Sided Quote Type USA Fab Quote Taiwan Fab Quote China Fab Quote Assembly Quote Advertised Specials Get a free prototype with your next production order
