Industry Directory | Consultant / Service Provider
Design and manufacture of thermal systems for rapid temperature verification and testing, and process cooling. Includes small-footprint thermal chambers and plates, mobile temperature forcing systems, and process chillers.
Industry Directory | Manufacturer
environmental test chamber manufacturers and vibration test system suppliers. Including climate test chamber, thermal shock test chamber, stability test chamber, ESS chamber, walk-in test chamber, altitude test chamber,
New Equipment | Cable & Wire Harness Equipment
Flag terminal NTC thermistor temperature sensor probe, surface mount housing, tin-plated copper flag terminal, with stud mounting hole, applied in industrial equipment, transit, HVAC , power and utilities, computers, home appliances, calibration and
HTCC QFN Packages to 40GHz High Temperature Co-Fired Ceramic (HTCC) QFN packages from Barry Industries feature low-loss broadband transitions for superior performance over frequency. HTCC construction provides for enhanced mechanical strength and h
Electronics Forum | Thu Jan 20 16:06:38 EST 2000 | Mike Naddra
Regarding glass transition , does anyone have expierance glass wiht transition temperature specification , such as what are the detrimental effects of exceeding the Tg , how long over the glass transition temperature ,if any , is acceptable. Tg of di
Electronics Forum | Fri Jan 21 14:51:08 EST 2000 | Dave F
Mike: I�d hate to see you making design decisions, based solely on the discussion here, but that this would be an impetus to consult IPC-D-279, "Design Guidelines ... " and take a course on designing reliable boards. Werner Engelmaier (Engelmaier
Used SMT Equipment | General Purpose Equipment
Espec Panelized EWPT 3468 - CCW Walk-In Temperature Chamber Brand: Espec Model: EWPT 3468 - CCW Serial#: 305536 Vintage: 2003 Power: 460V 3PH 60Hz. Temperature Control System: Balanced Temperature Control System: BTC Ambient Temperature:
Industry News | 2020-01-07 11:09:15.0
IPC-8921 establishes classifications and designations for woven and knitted e-textiles integrated with e-fibers, e-yarns and e-wires. It also standardizes key characteristics and durability testing for these materials as well as the industry test methods to be used to test against those characteristics.
Technical Library | 2014-06-19 18:13:23.0
For high-density electronic packaging,the application of flip-chip solder joints has been well received in the microelectronics industry. High-lead(Pb) solders such as Sn5Pb95 are presently granted immunity from the RoHS requirements for their use in high-end flip-chip devices, especially in military applications. In flip-chip technology for consumer electronic products, organic substrates have replaced ceramic substrates due to the demand for less weight and low cost. However, the liquidus temperatures of high-Pb solders are over 300°C which would damage organic substrates during reflow because of the low glass transition temperature. To overcome this difficulty, the composite solder approach was developed...
Technical Library | 2014-06-26 16:43:12.0
Edgebond adhesives have been widely used by the industry for improving the shock performance of area array packages. Most of the studies focus on the impact of material properties, such as coefficient of thermal expansion (CTE) and glass transition temperature (Tg), on reliability at room temperature. However, the operating temperature of a component on the printed circuit board bonded with edgebond adhesive can be close to or exceed Tg of the adhesive, where the material properties may be very different than at room temperature.
The Vortik VPm Progressive Cavity Pump dispensing two-component materials for encapsulation.
This video describes the features of BTU's Pyramax™ convection reflow oven, including the new dual-lane, dual-speed feature which essentially gives one oven the capability of two ovens. Pyramax ovens are known worldwide for superior reliability, unm
Career Center | San Jose, CA, California USA | Engineering,Production,Research and Development
Senior PCB Designer: Want to be part of an exciting pre-IPO enterprise B2B company working on the cutting edge of internet-of-things, artificial intelligence & agents, blockchain, and manufacturing technology? This well-funded venture-backed co
SMTnet Express, August 26, 2021, Subscribers: 26,759, Companies: 11,431, Users: 26,816 Low Melting Temperature Sn-Bi Solder: Effect of Alloying and Nanoparticle Addition on the Microstructural, Thermal, Interfacial Bonding
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/RSS_determine-hole-size-for-plastic-peg-alignment-pins_topic720.xml
(Glass Transition Temperature)... Author: Tom HSubject: 720Posted: 29 Dec 2012 at 2:51pmThe Tg (Glass Transition Temperature) relates to the PCB expansion in the "Y" axis or board thickness
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dima/processes/heat-staking-systems?con=t&page=4
Heat Staking Systems | Nordson DIMA DIMA Products Corporate | Global Directory | Languages Division Only All of Nordson Heat Staking Systems Heat Staking process De-forming the plastic is achieved by heating it to a temperature above the glass transition temperature via the use
winsouce.jpg)
