Industry Directory | Consultant / Service Provider
Florachem provides cleaning agents including products for defluxing,stencil/misprint cleaning and removal of white residue. We also supply rosin derivatives for manufacture of solder fluxes and pastes
New Equipment | Solder Materials
Kapp Lunar Flux™ is a slurry designed specifically for soldering casted Aluminum, Diecast, Zamak, White Metal and Pot Metal using Alumite™ solder. Residue is electrically conductive and slightly corrosive. Any flux residue should be removed with warm
Your very best choice for lead-free fluxes and pastes, this cleaner is the least-expensive nonflammable, ozone-safe cleaner on the market today. Not only does it remove lead-free residues, it actually prevents the formation of white residues. It's no
Electronics Forum | Mon Jul 01 00:09:47 EDT 2002 | Ben
Hi all How can I clean the white residue between QFP 0.5 mil Pitch? The white residue was created from mistake adding liquild No-clean flux Lonco 23F for reworking clean board. I can clean almost of it by using EC7M cleaning solvent except between
Electronics Forum | Wed Jan 27 19:42:34 EST 1999 | parag palshikar
i am working with the noclean process and getting white residues on the bottomside of the board probably due to the wave soldering flux.i am using a no-clean solder paste and a noclean wave solder flux.The boards passed the accelerated temperature a
Industry News | 2008-09-29 09:33:53.0
ROSEMONT, IL � Industry-leading associations IPC and SMTA jointly announce that Dave Torp, IPC Vice President of Technology and Standards, will moderate a collaborative panel discussion on cleaning equipment designs. The panelists will comprise cleaning equipment experts including Steve Stach of Austin American Technology, Mike Konrad of Aqueous Technologies, Jim Timler of Steolting/Trek, John Neiderman of Speedline Technologies, Roger Travato of Technical Devices, and Eric Larson of Crest Ultrasonic. The symposium, jointly sponsored by IPC and SMTA, will be held at Crowne Plaza Chicago O'Hare in Rosemont, IL on October 28-29, 2008.
Industry News | 2008-09-02 17:41:24.0
ROSEMONT, IL � Industry-leading associations IPC and SMTA jointly announce that Dr. Bill Kenyon will moderate a collaborative panel discussion on cleaning fluid designs. The panelists will comprise industry experts including Dr. Ken Dishart formerly of DuPont, Karl Manske of 3M, Tom Tattersall of MicroCare, Kyle Doyel of Kyzen, Dr. Harald Wack of Zestron, and Dr. Jay Soma of Petroferm. The symposium, jointly sponsored by IPC and SMTA, will be held at Crowne Plaza Chicago O'Hare in Rosemont, IL on October 28-29, 2008.
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
Technical Library | 1999-05-07 10:47:00.0
White residue remaining after cleaning circuit board assemblies can be caused by a variety of chemicals and reactions. Rosin and water-soluble fluxes, circuit board resins and epoxies, component materials and other contamination all contribute to this complex chemistry. This paper discusses many of the sources of the residues that seem to be an ever-increasing occurrence.
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
SMTnet Express, October 7, 2021, Subscribers: 26,641, Companies: 11,452, Users: 26,882 Cleaning Before Conformal Coating Cleaning PCBs before conformal coating removes potentially harmful and unknown contaminants from the board
| https://pcbasupplies.com/leaded-solder-wire/
levels Clear flux residue offers superior cosmetics No Clean Leaded Flux Cored Solder Wire JM-20 Sn63/Pb40 Specs Product Name Solder Wire JM20 Sn60 Pb40 Product Category Solder Wire Flux content (%) 1.0 - 3.0 Halide content
Precision PCB Services, Inc | https://precision-pcb-services-inc.com/products/smd4300tf10-tacky-flux-in-10cc-syringe-no-clean-water-washable-w-plunger-tip
SMD4300TF10 - Tacky Flux in 10cc syringe no-clean water-washable w/plu – Precision PCB Services, Inc. Search Log in or Create account Cart
COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.
2481 Hilton Drive
Gainesville, GA USA
Phone: (770) 538-0411