Industry Directory | Manufacturer
Alltemated sets the standard for tape and reel packaging, IC programming, lead trim/forming, bake and dry-pack services and carrier tape manufacturing.
Industry Directory | Manufacturer
Bosch Static Control is a specialist in ESD & CLEANROOM Production Items and has several years experience in this specialist field.We have our very own production Facilties in Dongguan, China
The MSL baking process at OX3 Corporation, (�MSL� stands for Moisture Sensitivity Level), is in accordance with IPC and JEDEC Standard "J-STD-033A," the joint industry standard for semiconductor handling, packing, shipping and the use of moisture/ref
Mechatronika MR10 is a fully programmable far infra red oven, suitable for reflow soldering as well as glue heat drying. Soldering sections are controlled by a microprocessor, that also enables the storage of up to sixteen parametrized temperature
Electronics Forum | Wed Feb 23 17:24:06 EST 2005 | Austinj
Solder spattering, solder balls, components "popping" off pads........ Not a serious chemical reaction, however, as replied to by KEN on 12/21/04 in a similar article: "Are you adding liquid flux? Or paste "Gel" flux? If liquid flux: This, in my m
Electronics Forum | Mon Dec 02 16:25:06 EST 2002 | jimlew
In doing process qualifications for 0201 caps, has anyone taken cross-sections and discovered cracks / hairline fractures / voids between the metalization on the end and the ceramic itself? (not cracks in the solder joint) We are well within the cap
Used SMT Equipment | Pick and Place/Feeders
Product number: YS88 Products in detail The characteristics of Configurable ~ 0402 chip - 55 mmcomponents, the wide range of special-shaped long joint element The height of the object elementcorresponds to 25.5 mm 10 ~ 30 n can be easy to stick
Used SMT Equipment | SMT Equipment
Product name: YS88 multi-function module chip mounter Product number: YS88 Products in detail The characteristics of Configurable ~ 0402 chip - 55 mm components, the wide range of special-shaped long joint element The height of the object elem
Industry News | 2018-10-18 08:00:40.0
SMT solder joint quality and appearance inspection process
Industry News | 2018-10-18 08:01:00.0
SMT solder joint quality and appearance inspection process
Parts & Supplies | SMT Equipment
YAMAHA KKE-M2267-00 GUIDE X AXIS YS24/ YG12 GUIDE ,X AXIS 1 KKE-M0201-00 XB AXIS SUB ASSY 1 2 KKE-M2267-00 GUIDE, X AXIS 1 3 KHY-M220A-00 TAPE, X DUCT 1 4 KHY-M220B-00 TAPE 2, X DUCT 1 5 KHY-M220C-00 TAPE 3, X DUCT 1 6 KHY-M226B-01 COV
Parts & Supplies | SMT Equipment
YAMAHA KKE-M2267-00 GUIDE X AXIS YS24/ YG12 GUIDE ,X AXIS 1 KKE-M0201-00 XB AXIS SUB ASSY 1 2 KKE-M2267-00 GUIDE, X AXIS 1 3 KHY-M220A-00 TAPE, X DUCT 1 4 KHY-M220B-00 TAPE 2, X DUCT 1 5 KHY-M220C-00 TAPE 3, X DUCT 1 6 KHY-M226B-01 COV
Technical Library | 2017-08-17 12:28:30.0
At SMT assembly, flux outgassing/drying is difficult for devices with poor venting channel, and resulted in insufficiently dried/burnt-off flux residue for no-clean process. Examples including: Large low stand-off components such as QFN, LGA Components covered under electromagnetic shield which has either no or few venting holes Components assembled within cavity of board Any other devices with small open space around solder joints
Technical Library | 2020-12-10 15:49:40.0
Electronic assemblies should have longer and longer service life. Today there are partially demanded 20 years of functional capability for electronics for automotive application. On the other hand, smaller components, such as resistors of size 0201, are able to endure an increasing number of thermal cycles until fail of solder joints, so these are tested sometimes up to 4000 cycles. But testing until the end of life is essential for the determination of failure rates and the prognosis of reliability. Such tests require a lot of time, but this is often not available in developing of new modules. A further acceleration by higher cycle temperatures is usually not possible, because the materials are already operated at the upper limit of the load. However, the duration can be shortened by the use of liquids for passive tests, which allow faster temperature changes and shorter dwell times because of better heat transfer compared to air. The question is whether such tests lead to comparable results and what failure mechanisms are becoming effective. The same goes for active temperature cycles, in which the components itself are heated from inside and the substrate remains comparatively cold. This paper describes the various accelerated temperature cycling tests, compares and evaluates the related degradation of solder joints.
Humitector™ Type 2 Humidity Indicator Card, used together with a Desi Pak® desiccant, can help provide a complete history of a dry pack environment for moisture sensitive surface mount devices (SMD's) (MSD - moisture sensitive
A Sustainable Alternative - Humitector cards are halogen-free and cobalt dichloride free. Visit https://www.clariant.com/solutions/products/2017/10/31/00/12/humitector-type-2-nonreversible-humidity-indicator-card?utm_source=CLRYouTube&utm_medium=Vi
KingFei SMT Tech | https://www.smtspare-parts.com/sale-37408125-kw1-m155l-00-cl8x2-0201-green-feeder-hand-kw1-m175l-00x-cl8x2mm-feeder-0402-hand-blue.html
KW1-M155L-00 CL8X2 0201 Green Feeder Hand KW1-M175L-00X CL8x2mm Feeder 0402 Hand Blue Leave a Message We will call you back soon
| https://www.eptac.com/faqs/ask-helena-leo/ask/wet-sponge-cleaning-vs-dry-brass-sponge-cleaning
Wet Sponge Cleaning vs. Dry Brass Sponge Cleaning - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more
