Industry Directory | Manufacturer
Carts and Cart based process methods that dramatically improve productivity of SMT production lines. Carts for SMT feeder storage and staging, SMT reels, SMT Stencils , Chip Tubes, Solder Pallets, PC
Affordable Manufacturing Execution System (MES), Shop Floor Automation and Integration Software CELLS WORKFLOW Product Tracking MES is an affordable full Manufacturing Process Control Software System providing Plant Intelligence for any industry.
New Equipment | Assembly Services
G9 + automatic vision printing machine is a new product for SMT high-end application field, which can perfectly meet the process requirements of 03015, 0.25pich and other fine spacing, high precision and high speed. Introduction to standard function
Electronics Forum | Sun Jan 24 04:34:19 EST 2010 | dearkim
I'm going to manage a efficiency of my SMT line. Final target is increase the output. But I don't make a decision of the efficiency index. What is the efficiency index in SMT line. In my opinion is... First, Output CPH/actual CPH(Based on optimized c
Electronics Forum | Sat Aug 17 07:34:36 EDT 2002 | bentzen
Hi Ken First of all, I think you are right to point out that the uptime should be calculated on the SMD line bottleneck. But I have some comments to your posting in general: The SMD line bottleneck, you say, is always the palcement machine. This i
Used SMT Equipment | In-Circuit Testers
Agilent 6633A The 6633A Power Supply 100 Watt, single output, series pass regulated supply is rated 50 V @ ?2 A. Both the voltage and current output can be programmed for either CV or CC operation. A built-in DCM and precision current shunt measu
Used SMT Equipment | In-Circuit Testers
Anritsu MP1763C The Anritsu MP1763C is used in combination with the Anritsu MP1764C or MP1764D Error Detector for 12.5G BER testing. The amplitude of the clock and data signals can be varied from 0.25 to 2 Vp-p while the offset can be adjusted to
Industry News | 2003-01-24 09:07:53.0
For Industrial, Telecom and Datacom Use
Industry News | 2016-10-20 19:25:04.0
The world market for printed circuit boards (PCBs) reached an estimated $58.6 billion in value in 2015 according to IPC’s World PCB Production Report for the Year 2015. This represents a nominal decrease of 2.7 percent from 2014, but factoring out the effects of exchange rate fluctuations, the growth of PCB output was actually up 2.0 percent in real terms.
Technical Library | 2018-04-27 13:23:31.0
When performing BGA component rework, it is important to know the actual heat that is coming out of the top and bottom heaters. This will be critical in setting up accurate heat profiles. Monitoring your heat output will also keep you aware of your heaters performance so that you will know when the heaters need to be replaced.
Technical Library | 2016-02-04 19:11:47.0
In a typical mechatronic manufacturing functional test setup, actual load simulations are usually done by connecting the DUT outputs to power or ground in order to establish either a high or low side driver. Each output is connected with different load and the test will either be sequential or concurrent. At lower power levels, these can usually be managed with general purpose switches. However, when it comes to higher power levels of currents more than 5 amps, such switching and loading might pose a greater challenge. Furthermore, critically in the manufacturing line, the tradeoff between cost and test time would have a great influence on the test strategy.This paper will present some key points to design a cost effective high power switching and load management solution.
www.unisoft-cim.com/cells.html - CELLS WORKFLOW is affordable, simple to setup & use yet powerful product & job tracking software for fast New Product Introduction (NPI). The CELLS WORKFLOW software provides total traceability in manufacturing floor
https://www.ascen.ltd/Products/Solder_paste_printer/513.html full auto PCB screen printer and SMT solder paste printing machine with Image and optical system,It is a very accurate fully automatic SMT stencil printer.automatic PCB screen printer main
Career Center | Sunrise, Florida USA | Technical Support
local area field srevice technician fixing or replacing desktops and POlocal S's
Career Center | Riyadh 11623, Philippines | Engineering,Maintenance,Production
PROFESSIONAL EXPERIENCE: Connected in the field of manufacturing/electronics industry experienced in the line, Through Hole and Surface Mount Technology, worked on various Fuji Machines Universal model, such as: CP 643E chip shooter QP 242E chip mou
Production Line Dynamics: What Count Is What Actually Comes Out Of Your Line Production Line Dynamics: What Count Is What Actually Comes Out Of Your Line In high-volume production, it is the price of the end product that matters. Purchasing
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/news/news/2015-01-07
New Plasticizing Unit Delivers Enhanced-Quality Melt and Boosts Output in High-Speed Molding of Thin-Wall Packaging | Nordson POLYMER PROCESSING SYSTEMS Polymer Processing Systems
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/688951_OvenSetupWizard-XP4021.pdf
. New Recipe Power Maximum Output: 80%. Power up Delay Time: 5 sec During startup, next group of heater channels will turn on after all channels in current startup group drop below “..Maximum Output %” and then “Power up Delay Time