Industry Directory | Manufacturer
The exclusive supplier of SIPAD Solid Solder Deposit in North America and the only SIPAD Solid Solder Deposit (SSD) coating service bureau in the world.
Industry Directory | Manufacturer
A manufacturer of desoldering braid (wick) with an emphasis on continuing advancement in soldering/desoldering technology, visual and x-ray inspection systems, fume extraction, and solder paste inspection systems.
Flux application using the DispenseJet® pump is a superior alternative to screen printing and ultrasonic spray. Jet dispensing eliminates the overspray and material waste associated with ultrasonic and spray application methods. Flux application usi
New Equipment | Rework & Repair Equipment
The BEST EZReball™ process is the answer to your reballing problems. This BGA reballing process simplifies the process while eliminating the clean up of all those paper remnants, allowing for better yields and faster reballing times. The simplicity o
Electronics Forum | Wed Oct 23 08:40:20 EDT 2002 | davef
Yer not making this easy. What kind of flux? If no-clean flux, what controls are you using to assure you are: * Applying the correct amount of flux? * Properly activating the flux? If water washable flux, talk to us about your cleaning methods and
Electronics Forum | Thu Jan 20 09:49:08 EST 2005 | Mike Konrad
Regarding the reference (Patrick) to a previous thread promoting �no-residue� fluxes, I must say that there is absolutely no such thing as �No-Residue� flux. There are �Low-Residue� fluxes and even �Very-Low� residue fluxes but to suggest that there
Industry News | 2003-03-21 08:12:24.0
Tecan reckons it is consistently producing what may be regarded as the most efficient stencils in the world today.
Industry News | 2018-10-18 09:20:09.0
Product defects caused by the flux in the wave soldering process
Parts & Supplies | Soldering - Wave
Spray-on Fluxer Device TAF40-12V, TAF40-15PV This is an automatic spray device to apply the post-flux: It is used in order to better soldering effect when you use the Wave Soldering Device (below). You can change the amount of the post-flux qui
Parts & Supplies | Soldering - Wave
Spray-on Fluxer Device TAF40-12V, TAF40-15PV This is an automatic spray device to apply the post-flux: It is used in order to better soldering effect when you use the Wave Soldering Device (below). You can change the amount of the post-flux qui
Technical Library | 2017-12-11 22:31:06.0
Typical printed circuit board assemblies (PCBAs) processed by reflow, wave, or selective wave soldering were analysed for typical levels of process related residues, resulting from a specific or combination of soldering process. Typical solder flux residue distribution pattern, composition, and concentration are profiled and reported. Presence of localized flux residues were visualized using a commercial Residue RAT gel test and chemical structure was identified by FT-IR, while the concentration was measured using ion chromatography, and the electrical properties of the extracts were determined by measuring the leak current using a twin platinum electrode setup. Localized extraction of residue was carried out using a commercial C3 extraction system. Results clearly show that the amount and distribution of flux residues are a function of the soldering process, and the level can be reduced by an appropriate cleaning. Selective soldering process generates significantly higher levels of residues compared to the wave and reflow process. For conformal coated PCBAs, the contamination levels generated from the tested wave and selective soldering process are found to be enough to generate blisters under exposure to high humidity levels.
Technical Library | 2019-07-24 23:55:32.0
Voiding is a key concern for components with thermal planes because interruptions in Z-axis continuity of the solder joint will hinder thermal transfer. When assembling components with solder paste, there is a high propensity for voiding due to the confined nature of the solder paste deposits under the component. Once reflowed, many factors contribute to the amount of voiding in a solder joint such as the reflow profile, designs of the component, board and stencil, and material factors. This study will focus on the solder paste alloy and flux combination as well as profile and board surface finishes.
Flux spray coating on a PCB with uniformal thickness down to 5 microns, with clear edge definition and minimal overspray. Can coat large or shoot dots with the same jet.
Camera Module Cleaning Machine ETA-C800 If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA Cleaning Machine, On-line PCBA Cleaning Machine
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 1
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 2
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/select/technologies-or-options/spray-fluxing
. The amount of flux sprayed is controlled by the value open time, reservoir air pressure and needle stroke. The area of spray coverage is determined by
| http://etasmt.com/cc?ID=te_news_bulletin,24961&url=_print
system is to collect a significant amount of the flux; permitting a minimum amount of flux vapor from escaping into the customer’s plant exhaust system
.gif)
