GPD Global | https://www.gpd-global.com/pdf/lead-former/CF9-User-Guide-901-1-07.pdf
. CF-9 User's Guide ii GPD Global 09/30/92 Safety Instructions Symbol samples and definitions for the DANGER, WARNING, CAUTION, IMPORTANT and NOTE safety notices used in this document are as follows: ** D A N G E R
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF9-Doc-Package-901-1-01.pdf
eccentric bushing in the eccentric crank (Item 1) in die block's top half (T1 or T2). b. Slip wear plate face up between cover plate and slide. c. Align wear plate counter sunk holes with cover plate set screws. d. Install new set screws and lightly tighten
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF9-Doc-Package-901-1-01.pdf
eccentric bushing in the eccentric crank (Item 1) in die block's top half (T1 or T2). b. Slip wear plate face up between cover plate and slide. c. Align wear plate counter sunk holes with cover plate set screws. d. Install new set screws and lightly tighten
GPD Global | https://www.gpd-global.com/co_website/pdf/lead-former/CF8-User-Guide-801-1-07.pdf
. 04/02/07 GPD Global® CF-8 Precision Axial Lead Former 04/02/07 ii Warranty GPD Global® (GPD) warrants that this product will be free from defects in material and workmanship for a period of one (1
GPD Global | https://www.gpd-global.com/pdf/lead-former/CF8-User-Guide-801-1-07.pdf
. 04/02/07 GPD Global® CF-8 Precision Axial Lead Former 04/02/07 ii Warranty GPD Global® (GPD) warrants that this product will be free from defects in material and workmanship for a period of one (1
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20170118-PBT-002P-FORCEWare-v5-6-3.pdf
. InstaCal is copyrighted by Measurement Computing. Windows is registered trademark of Microsoft Corporation in the United States and/or other countries
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20170118-PBT-002P-FORCEWare-v5-6-3.pdf
. InstaCal is copyrighted by Measurement Computing. Windows is registered trademark of Microsoft Corporation in the United States and/or other countries
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20170830-PBT-002P-FORCEWare-v5-7-0.pdf
wheel (Item 4), aligning the tape holes with the draw wheel pins. d. Release the draw wheel rollers by pushing down on the draw wheel handle. The spring-loaded knob releases the rollers to hold the tape in place. 4. If necessary, use the adjusting knob
GPD Global | https://www.gpd-global.com/pdf/pbt/PBFT-VS-SPC-User-Guide-20170830-PBT-002P-FORCEWare-v5-7-0.pdf
wheel (Item 4), aligning the tape holes with the draw wheel pins. d. Release the draw wheel rollers by pushing down on the draw wheel handle. The spring-loaded knob releases the rollers to hold the tape in place. 4. If necessary, use the adjusting knob
GPD Global | https://www.gpd-global.com/co_website/pdf/pbt/PBFT-VS-SPC-User-Guide-20170519-PBT-002P-FORCEWare-v5-6-3.pdf
carriage in place. d. Select a speed on the speed selector (Figure 1, Item 3). e. Press TEST START (Figure 2, Item 1). The following should occur: • Tape carriage will automatically travel to the end of its range and stop. • The TEST START lamp will darken