New Equipment | Cleaning Equipment
Stencil Wiping Rolls are used to remove residual solder paste from the bottom side of PC Board stencils. Using Stencil Wiping Rolls prevents smearing, bridging, and solder balls caused by normal printing of solder paste onto PC Boards. We manufactur
New Equipment | Cleaning Equipment
clean wiper roll are used to remove residual solder paste from the bottom side of PC Board stencils. Using Stencil Wiping Rolls prevents smearing, bridging, and solder balls caused by normal printing of solder paste onto PC Boards. Specifications:
Electronics Forum | Fri Jul 06 03:23:01 EDT 2001 | kennyhktan
Hi there Steven ! Please allow me to share some of my problem we're facing here with you. Here are a few points that I suggest you should check on your current process:- (1)PCB - Component land partern design ? It is per IPC spec ? - Mask
Electronics Forum | Thu Feb 11 14:36:42 EST 1999 | Evelyn York
Hey, has anybody experienced problems with solder balls falling off BGA's? I have not been able to identify a contaminant nor any physical problems that would cause this. On packages with 'good' adhesion I have not observed any intermetallic form
Industry News | 2003-02-17 08:40:25.0
To Meet Government Environmental Standards and Individual Company Policies, While Satisfying Production Requirements
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Technical Library | 2007-02-01 09:57:15.0
The rapid assimilation of Ball Grid Array (BGA) and other Area Array Package technology in the electronics industry is due to the fact that this package type allows for a greater I/O count in a smaller area while maintaining a pitch that allows for ease of manufacture.
Technical Library | 2016-11-30 21:30:50.0
Mid-chip solder balling is a defect typically associated with solder paste exhibiting poor hot slump and/or insufficient wetting during the reflow soldering process, resulting in paste flowing under the component or onto the solder resist. Once molten, this solder is compressed and forced to the side of the component, causing mid-chip solder balling.This paper documents the experimental work performed to further understand the impact on mid-chip solder balling from both the manufacturing process and the flux chemistry.
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
· What is the difference between SMT vacuum reflow soldering machine and ordinary reflow soldering machine? · What problems can be solved by smt vacuum reflow soldering machine? · What is the basic principle of vacuum reflow machine? · Ho
Training Courses | | | PCB Inspection Courses
The PCB inspection courses focus on improving PCB yield and reliability through validation and detection of defects on electronics assemblies.
Events Calendar | Mon Mar 16 00:00:00 EDT 2020 - Mon Mar 16 00:00:00 EDT 2020 | ,
BGA & Area Array Failures, Causes & Corrective Actions Online Webinar
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 1
Career Center | san diego,, California USA | Engineering,Production,Quality Control,Technical Support
SMT Process Engineer, ISO-9001, IPC-600/610/620/7711/7721, J-STD-001, Thermal profiling, Lean manufacturing.
SMT Express, Volume 2, Issue No. 3 - from SMTnet.com Volume 2, Issue No. 3 Thursday, March 16, 2000 Featured Article Return to Front Page Curtailing Voids in Fine Pitch Ball Grid Array Solder Joints by Gary Morrison and Kevin Lyne
Imagineering, Inc. | https://www.pcbnet.com/blog/causes-of-pcb-warping-how-to-prevent-it/
Causes of PCB Warping & How to Prevent It | Imagineering, Inc. Skip to main content Resources Support Contact Us FAQs Live Chat My Account 847-806-0003 Menu PCB Capabilities Fabrication Technology Roadmap Materials Available HDI Tolerances Certifications
| https://www.eptac.com/webinars/hot-topics-solder-mask-bubbles-and-mask-flaking-solder-balls-rohs-cable-coating-and-more/
Hot Topics: Solder Mask Bubbles and Mask Flaking, Solder Balls, RoHS Cable Coating and More - EPTAC - Train. Work Smarter. Succeed Looking for solder training standards, manuals, kits, and more
winsouce.jpg)
