Specializing in manufacturing pH, ORP & Ion Selective sensors for difficult process control aplications. Offering a full line of process control instrumentation.
Hydrotrue® RO 200 series water treatment system Designed for DriSteem equipment and stand-alone operation, the Hydrotrue RO 200 series reverse osmosis water treatment system significantly reduces or eliminates maintenance on downstream equipment by r
Hydrotrue® RO 400 series water treatment system Designed for DriSteem equipment and stand-alone operation, the Hydrotrue RO 400 Series reverse osmosis water treatment system significantly reduces or eliminates maintenance on downstream equipment by r
Electronics Forum | Thu Nov 03 07:22:16 EST 2005 | davef
arnold: I did not say that Sn100 dissolved copper faster. The graph of dissolution rates [from the link above] shows that Sn100 dissolves copper slower than many of the other solders.
Electronics Forum | Wed Mar 12 11:41:41 EDT 2008 | gregoryyork
Blimey just seen the picture that is bad. You could try to dissolve some of the residue/gunge in IPA if it is flux residue it should readily dissolve if it is resist issue then only portions will dissolve leaving a white powder which is Talc If you
Industry News | 2011-10-12 20:28:30.0
Kyzen announces that Ram Wissel will present “Solubility Theorems” at SMTA’s Penang Expo & Technical Forum.
Industry News | 2015-07-21 07:44:37.0
ViTrox officially announces that it has discontinued its sales representative agreement with Interlatin Mexico effective immediately.
Parts & Supplies | Soldering - Wave
Spray-on Fluxer Device TAF40-12V, TAF40-15PV This is an automatic spray device to apply the post-flux: It is used in order to better soldering effect when you use the Wave Soldering Device (below). You can change the amount of the post-flux qui
Parts & Supplies | Soldering - Wave
Spray-on Fluxer Device TAF40-12V, TAF40-15PV This is an automatic spray device to apply the post-flux: It is used in order to better soldering effect when you use the Wave Soldering Device (below). You can change the amount of the post-flux qui
Technical Library | 2019-05-23 10:38:07.0
Solvent and co-solvent cleaning involves the use of engineered solvents in a vapor phase system. The solvents classically used were Class 1 Ozone Depleting Substances, but new types of solvents have been developed that are less environmentally harmful. In some cases, isopropyl alcohol is used with a co-solvent. In these types of cleaning systems, a cloud of boiling vapor solvent is maintained between a boil sump and a cooling coil. When the items to be cleaned are immersed in the vapor cloud, the solvent condenses on the assemblies and acts to dissolve the residues. These processes usually involve a final rinse step outside of the vapor cloud to ensure that all dissolved residues are washed off the assemblies (Figure 1).
Technical Library | 2010-06-10 21:01:48.0
This paper researches the effectiveness of the R.O.S.E. cleanliness testing process for dissolving and measuring ionic contaminants from boards soldered with no-clean and lead-free flux technologies.
Automatic Concentration Monitoring System ZESTRON® EYE is a digital monitoring system that enables the precise measurement and control of the cleaning bath concentration for electronics cleaning processes in real time even in presence of dissolved c
Incorporating the ZESTRON® EYE's 3P-Technology, the ZESTRON® EYE CM monitors and controls wash bath concentration in real time. This stand alone concentration management system easily integrates with batch and inline cleaning systems. It is independe
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 1
Events Calendar | Tue Apr 13 00:00:00 EDT 2021 - Tue Apr 13 00:00:00 EDT 2021 | ,
Boston Chapter Webinar: Cleaning Chemistry For PWB and Rework - Part 2, session 2
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/your-process/fluid-types/conformal-coating-materials
. Repair can be done by dissolving the coating, and after repair new coating can be applied without creating any stratified seams. Polyurethane materials are mostly solvent based, but also exist as water-based solutions
| https://www.eptac.com/faqs/ask-helena-leo/ask/multiple-wash-steps-affecting-resistance-characteristics
solvent is not dissolving the resistive ink. This is all part of the qualification process when component are selected or when cleaning solvents are selected for manufacturing
