Industry Directory | Manufacturer
A manufacturer of desoldering braid (wick) with an emphasis on continuing advancement in soldering/desoldering technology, visual and x-ray inspection systems, fume extraction, and solder paste inspection systems.
S8, S10, S12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
E8, E10, E12 - 8, 10 or 12 top/bottom cooling zones. Heating System: Up to twelve groups of top and bottom forced hot air convection heating zones. Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air con
Electronics Forum | Wed Sep 29 09:29:47 EDT 2010 | swag
Take a few parts from the reel and look close at the parts to make sure the bottom surface of the leads is below the bottom surface of the body.
Electronics Forum | Thu Sep 30 11:30:46 EDT 2010 | babe7362000
Take a few parts from the reel and look close at > the parts to make sure the bottom surface of the > leads is below the bottom surface of the body. Yes I did that and they are below the body. I found the problem I think. The solder mask is abo
Used SMT Equipment | Soldering - Reflow
Heating zones: 5 Cooling zones: 2 Total heating length: 66 in. Total cooling length: 26 in. Total process length: 127 in. Total on /off load length: 11 in. Overall system length: 138.5 in. Overall system width: 52 in. Overall system height: 5
Used SMT Equipment | Soldering - Reflow
Perfect condition. 10 heating zones three cooling zones Power hood lifts RS-232 interface with PID microprocessorbased controller Combination belt and edge/rail conveyor Safety interlocks on electrical panels Over temp
Industry News | 2018-10-18 08:14:11.0
How to Prevent the Tombstone and Open Defects during the SMT Reflow Process
Industry News | 2013-09-03 11:52:21.0
BEST's EZReball(TM) reballing preforms now are available as standard in 3 business days. Expedited packs are in available in 24 hours to help you with your reballing projects
Parts & Supplies | SMT Equipment
03059051-01 Lifting Table Dual Conveyor X4i 03059195-01 Retrofit kit pneumatic unit D1 03059196-01 Gas Spring 400N ( for D1/D2 Left Hood) 03059238S01 Linear Dipping Unit (LDU) Basis 03059375-01 Starter kit filter disc 2-parts / C+
Parts & Supplies | Chipshooters / Chip Mounters
> JUKI ESL13000000 VACUUM PAD 15 JUKI ESL13000100 PHOTO MICRO SENSOR A JUKI ESL13001000 TUBE union (KL700) JUKI ESL130011A0 CONVEYOR MOTOR (KZ500) JUKI ESL13002000 CLAMP LEVER JUKI ESL13003000 T TYPE NUT JUKI ESL130031A0 OPERATION PANEL (KL700) JUKI
DescriptionThe Electrovert® Electra™ is an advanced, meticulously engineered wave soldering system designed for high-mass and high-volume manufacturers. Although intended for maximum throughput requirements, the Electra also offers maximum process fl
Career Center | Raleigh, North Carolina USA | Engineering
Title: SMT PROCESS ENGINEER Salary: 70k-80k max rate with great benefits Job Description: ESSENTIAL DUTIES & RESPONSIBILITIES To perform this job successfully, an individual must be able to perform each essential duty satisfactorily, plus w
| http://etasmt.com/cc?ID=te_news_bulletin,24761&url=_print
. The flux cooling modules are easily removed by lifting straight up and out of rear of the oven ’ s top shell. The weight of each clean cooling module is 19.5 lbs (8.8 kg
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/dryers?con=t&page=8
– from simple, manual systems to the most sophisticated, programmable, automated systems. Linak Profiles: Efficient and very consistent powder coating Industrial Coating Systems Linak Profiles, Denmark, converted its production to solve its growth-related capacity requirements for lifting columns while
