Orion provides flexible, polyurethane filter foam to remove dust and contaminating particles from the air, gases and liquids in a variety of applications. The open pore skeletal structure provides low air resistance ideal for use in computers, electr
Crane bar solder are made from gradeA Virgin metals Bars:1/4,1/2and1 Lb. Cakes-3 lb.4"dia. Ingot or pig-50 lbs.Ribbon .oo2 to .125"T in W to4" Wire solid to flux cored sizes .500dia-.005Dia
Electronics Forum | Tue May 26 15:39:16 EDT 2009 | mikesewell
Amkor's MLF guidelines are very similar to Actels. 1 to 1 on the stencil to part pad on the I/O pads, 75% with a grid windowpane, 0.125 mm/5 mil stencil. For example, the Actel area ratio for a 0.3 mm sq. pad and 0.125 mm stencil is 0.6 which seems
Electronics Forum | Wed Sep 22 01:35:27 EDT 2021 | david0811
hi, i looking for MPM125 manual operation and also datasheet. please assist
Used SMT Equipment | Pick and Place/Feeders
Hundreds of Quad feeder overstock. Prices 8mm 5 volt NON IQ $75.00 8mm - 12 Volt IQ $125.00 16mm -IQ $150.00 24mm - IQ $200.00
Used SMT Equipment | Pick and Place/Feeders
Spare parts for Universal Radial and Axial through-hole insertion machines (RAD5 6360D, RAD8 6380A, RAD8 XT 6380B, VCD5 6241D, VCD8 6241F, VCD Dual 6292A, SEQ 2596A, SEQ5, SEQ8). UIC Part Number / Part Description 15754 O'RING 15755 O'RING 15759
Industry News | 2018-10-18 10:43:28.0
Suggested 14 and 16 Layer Board Layouts
Industry News | 2011-09-06 15:20:36.0
SMTA China announced the Best Paper/Presentation and Best Exhibit Awards at its annual awards presentation held in conjunction with SMTA China and Hong Kong Chapter Breakfast Reception, which took place August 31, 2011 at the Ritz-Carlton Hotel in Shenzhen.
4.jpg)
Parts & Supplies | Assembly Accessories
YAMAHA Y1 AXIS 90K63-611404 MOTOR FOR YG100B Pick and Place Machine More Yamaha parts in stock KM9-M7107-00XSHFT, HEAD ASSYYV100II KM9-M7106-00XSHAFT HEAD ASSY YV100II KV8-M713S-A0X STD.SHAFT2,SPARE YV100X KV8-M712S-A0X STD.SHAFT1,SP
Parts & Supplies | Assembly Accessories
Yamaha Original FNC shaft For YV100XG Pick and Place Machine More Yamaha parts in stock KM9-M7107-00XSHFT, HEAD ASSYYV100II KM9-M7106-00XSHAFT HEAD ASSY YV100II KV8-M713S-A0X STD.SHAFT2,SPARE YV100X KV8-M712S-A0X STD.SHAFT1,SPARE YV
Technical Library | 2015-05-21 18:46:31.0
In this work the reliability of an embedded planar capacitor laminate under temperature and voltage stress is investigated. The capacitor laminate consisted of an epoxy-BaTiO3 composite sandwiched between two layers of copper. The test vehicle with the embedded capacitors was subjected to a temperature of 125oC and a voltage bias of 200 V for 1000 hours. Capacitance, dissipation factor, and insulation resistance were monitored in-situ. Failed capacitors exhibited a sharp drop in insulation resistance, indicating avalanche breakdown. The decrease in the capacitance after 1000 hours was no more than 8% for any of the devices monitored. The decrease in the capacitance was attributed to delamination in the embedded capacitor laminate and an increase in the spacing between the copper layers.
Technical Library | 2023-07-25 16:42:54.0
Printing solder paste for very small components like .3mm pitch CSP's and 01005 Chip Components is a challenge for the printing process when other larger components like RF shields, SMT Connectors, and large chip or resistor components are also present on the PCB. The smaller components require a stencil thickness typically of 3 mils (75u) to keep the Area Ratio greater than .55 for good paste transfer efficiency. The larger components require either more solder paste height or volume, thus a stencil thickness in the range of 4 to 5 mils (100 to 125u). This paper will explore two stencil solutions to solve this dilemma. The first is a "Two Print Stencil" option where the small component apertures are printed with a thin stencil and the larger components with a thicker stencil with relief pockets for the first print. Successful prints with Keep-Outs as small as 15 mils (400u) will be demonstrated. The second solution is a stencil technology that will provide good paste transfer efficiency for Area Ratio's below .5. In this case a thicker stencil can be utilized to print all components. Paste transfer results for several different stencil types including Laser-Cut Fine Grain stainless steel, Laser-Cut stainless steel with and w/o PTFE Teflon coating, AMTX E-FAB with and w/o PTFE coating for Area Ratios ranging from .4 up to .69.
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Cut and bend machine for taped axial components. axial component lead former be often used the axial resistance and diode. This is the motorized type former, you can use this axial lead f
https://www.ascen.ltd/Products/Automatic_SMT_equipment/PCB_conveyor/100.html PCB linking conveyor and PCB belt conveyor mainly used to connect different type PCB board handing equipment effectively for the SMT production line. ASCEN technology is ava
Events Calendar | Tue Jul 11 00:00:00 EDT 2023 - Tue Jul 11 00:00:00 EDT 2023 | Oshkosh, Wisconsin USA
Wisconsin Chapter In-Person Event: PCB Workshop and PCB Plant Tour
Career Center | , California USA | Engineering,Research and Development,Sales/Marketing
Director of Marketing and Communications needed for multi-continental electronics manufacturing organization. If you have a solid background in telecom, PC's, networking, storage, and digital consumer electronics - combined with a proven track recor
| https://www.feedersupplier.com/buy-btu_pyramax_125.html
Buy btu pyramax 125, Good quality btu pyramax 125 manufacturer Leave a Message We will call you back soon! Your message must be between 20-3,000 characters
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/47759001-key-125-189067?page=15&category=1111
UNIVERSAL KEY(125) 47759001 | QYSMT × Home about Us ABOUT US FAQ SMT spare parts SMT surplus equipment SMT peripheral equipments News Contact US 0 0 Sign in contact us Products AI SPARE PARTS KEY(125
