Technical Library: microwave and plasma (Page 1 of 1)

Metal-based Inkjet Inks for Printed Electronics

Technical Library | 2014-12-04 18:27:40.0

A review on applications of metal-based inkjet inks for printed electronics with a particular focus on inks containing metal nanoparticles, complexes and metallo-organic compounds. The review describes the preparation of such inks and obtaining conductive patterns by using various sintering methods: thermal, photonic, microwave, plasma, electrical, and chemically triggered. Various applications of metal-based inkjet inks (metallization of solar cell, RFID antennas, OLEDs, thin film transistors, electroluminescence devices) are reviewed.

Hebrew University of Jerusalem

Effect on Microwave Plasma Surface Treatment for Improved Adhesion Strenght of Direct Copper Plating on Polytetrafluoroethylene (PTFE)

Technical Library | 2016-01-07 19:13:23.0

The purpose of this study is to investigate the effect of plasma surface modification to improve adhesion strength between polytetrafluoroethylene (PTFE) and electroless copper plating. PTFE is widely used in many industries because of its unique electrical, thermal, and mechanical characteristics. However, because of its low surface energy, it is difficult to acquire enough adhesion strength between PTFE and other substances without surface modification. Plasma is well known as one of the surface modification techniques that improve adhesion strength.

Nissin Corporation

A Novel Method for the Fabrication of a High-Density Carbon Nanotube Microelectrode Array

Technical Library | 2016-11-03 17:53:56.0

We present a novel method for fabricating a high-density carbon nanotube microelectrode array (MEA) chip. Vertically aligned carbon nanotubes (VACNTs) were synthesized by microwave plasma-enhanced chemical vapor deposition and thermal chemical vapor deposition. The device was characterized using electrochemical experiments such as cyclic voltammetry, impedance spectroscopy and potential transient measurements. Through-silicon vias (TSVs) were fabricated and partially filled with polycrystalline silicon to allow electrical connection from the high-density electrodes to a stimulator microchip.In response to the demand for higher resolution implants, we have developed a unique process to obtain a high-density electrode array by making the microelectrodes smaller in size and designing new ways of routing the electrodes to current sources.

Hong Kong University of Science

Three-Dimensional MMIC and Its Evolution to WLCSP Technology

Technical Library | 2012-01-19 19:14:49.0

The history of multilayered, three-dimensional monolithic microwave integrated circuit (3-D MMIC) technology is described here. Although significant researches were carried out in the second half of 1990’s, still there were many twists and turns before an

Sumitomo Electric Industries, Ltd.

Additive Manufacturing for Next Generation Microwave Electronics and Antennas

Technical Library | 2020-08-13 00:59:03.0

The paper will discuss the integration of 3D printing and inkjet printing fabrication technologies for microwave and millimeter-wave applications. With the recent advancements in 3D and inkjet printing technology, achieving resolution down to 50 um, it is feasible to fabricate electronic components and antennas operating in the millimeter-wave regime. The nature of additive manufacturing allows designers to create custom components and devices for specialized applications and provides an excellent and inexpensive way of prototyping electronic designs. The combination of multiple printable materials enables the vertical integration of conductive, dielectric, and semi-conductive materials which are the fundamental components of passive and active circuit elements such as inductors, capacitors, diodes, and transistors. Also, the on-demand manner of printing can eliminate the use of subtractive fabrication processes, which are necessary for conventional microfabrication processes such as photolithography, and drastically reduce the cost and material waste of fabrication.

Georgia Institute of Technology

Conformal Surface Plasmons Propagating on Ultrathin and Flexible Films

Technical Library | 2013-09-05 17:44:14.0

Surface plasmon polaritons (SPPs) are localized surface electromagnetic waves that propagate along the interface between a metal and a dielectric. Owing to their inherent subwavelength confinement, SPPs have a strong potential to become building blocks of a type of photonic circuitry built up on 2D metal surfaces; however, SPPs are difficult to control on curved surfaces conformably and flexibly to produce advanced functional devices. Here we propose the concept of conformal surface plasmons (CSPs), surface plasmon waves that can propagate on ultrathin and flexible films to long distances in a wide broadband range from microwave to mid-infrared frequencies.

Southeast University (SEU)

  1  

microwave and plasma searches for Companies, Equipment, Machines, Suppliers & Information

Void Free Reflow Soldering

Training online, at your facility, or at one of our worldwide training centers"
Sell Your Used SMT & Test Equipment

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
SMT feeders

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Win Source Online Electronic parts

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.