Suppliers of Stencil/PCB Cleaners, Soldering Systems, Solder Paste Inspection & Measurement Systems, Ionic Contamination Test Systems, Spray Fluxers and Cleaning Chemicals
Industry Directory | Consultant / Service Provider / Manufacturer
ULT is a vendor of efficient fume extraction solutions for air purification. The company's systems are utilized for the removal of laser fumes, soldering fumes, odors, vapors, gases, dusts etc. in electronics production.
New Advanced Precision Auger Pump - Single Pump Solution The Precision Auger pump is designed to work with mid-to-high viscosity liquid such as glues, conductive, and non-conductive adhesive and pastes. The pump is controlled with a servo motor equ
New Equipment | Education/Training
Blackfox’s Lead Free Soldering series minimizes the risks of conversion, and gives you the confidence to introduce lead free products and services quickly, with highest quality. The lead free certification program offers the latest requirements for S
Electronics Forum | Wed May 17 23:45:05 EDT 2006 | smt_guru
The question to ask is not so much in contamination of this mixed technology metallurgies, but rather, will this metallurgy successfully coalesce into a reliable interconnect? I find in my consulting travels worldwide that many of my clients do not
Electronics Forum | Thu Nov 06 09:10:13 EST 2003 | successmani
hi, NEMI recommends separate solders for reflow sodlering and wave soldering. Reflow soldering- Sn-3.9Ag-0.7Cu Wave sodlering- Sn-0.7CU Wavesoldering- Sn-0.7Ag What will happen if a mixed technolgy PCb board containing both through hole and surface
Used SMT Equipment | Soldering - Wave
Vitronics Wave Soldering Machine Model: Delta 6622C Vintage: 2006 Lead-Free (SN100C) Internal Dual Spray Fluxer (2) Bottom-Side Convection Preheat Zones (1) Bottom-Side Cal Rod Preheat Zone (1) Top-Side IR Preheat Zone Cast Iron Solder Pot Mix of L a
Used SMT Equipment | AOI / Automated Optical Inspection
BF-Frontier is used in the inspection of large-size printed circuit boards. In this device, the unique control sequence of software and hardware, accelerated scanning mode and stable optical illumination system can allow BF-Frontier to easily complet
Industry News | 2012-09-13 09:35:40.0
GPD Global will exhibit in Booth #435 at the upcoming SMTA International Conference and Expo,
Industry News | 2012-06-11 12:24:54.0
GPD Global announces that it will exhibit in Booth #6085 North at the upcoming SEMICON West conference and exhibition, scheduled to take place July 10-12, 2012 at the Moscone Center in San Francisco, California.
Parts & Supplies | Solder Paste Mixers
Solder Cream Mixer Feature of Solder Cream Mixer Excellent for ISO 9000 solder paste mix process condition. Strong mixing power. Increasing printing quality. Cream Solder Mixer Led display panel and microprocessor control, easy to operate. Unive
Parts & Supplies | Solder Paste Mixers
Solder Cream Mixer Feature of Solder Cream Mixer Excellent for ISO 9000 solder paste mix process condition. Strong mixing power. Increasing printing quality. Cream Solder Mixer Led display panel and microprocessor control, easy to operate. Unive
Technical Library | 2019-08-08 10:23:51.0
High mix production is the mainstay of many electronics assembly plants. Lot sizes and board complexities vary and the boards are often mixed technology, comprising a blend of both surface mount and through-hole technology. Modularizing a production line enables a clear distinction between one type of assembly process and another. This article assumes a modern factory where a job can be routed to the selective soldering machine module, the hand assembly bench, or a combination of both. The decision rules of routing a circuit board through hand assembly versus automated selective soldering are discussed. Hand assembly soldering operations require no explanation.
Technical Library | 2020-03-09 10:50:17.0
A customer called the Helpline seeking advice for cleaning no-clean fluxes prior to applying a conformal coating. The customer's assemblies were manufactured with a no-clean rosin based solder paste (ROL0) and were cleaned with an isopropyl alcohol (IPA) wash. After cleaning, a white residue was sometimes found in areas with high paste concentrations and was interfering with the adhesion of the conformal coating (Figure 1). For conformal coatings to adhere properly, the printed circuit board (PCB) surface must be clean of fluxes and other residues. In addition, ionic contamination left by flux residues can lead to corrosion and dendrite growth, two common causes of electronic opens and shorts. Other residues can lead to unwanted impedance and physical interference with moving parts.
New Advanced Precision Auger Pump - Single Pump Solution The Precision Auger pump is designed to work with mid-to-high viscosity liquid such as glues, conductive, and non-conductive adhesive and pastes. The pump is controlled with a servo motor equ
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Fri Jan 11 00:00:00 EST 2019 - Fri Jan 11 00:00:00 EST 2019 | Richardson, Texas USA
SMTA Dallas Chapter - Understanding Selective Solder Technology
Events Calendar | Thu Jun 14 00:00:00 EDT 2018 - Fri Jun 15 00:00:00 EDT 2018 | ,
SMT Process Fundamentals for Tin-Lead and Lead Free Assembly - SMTA Webtorial
Career Center | Boulder, Colorado USA | Engineering,Production,Quality Control
Senior-level micro-electronic technician capable of independent manufacture of custom hybrids, focal plane assemblies, and prototype detector assemblies in cleanroom environment (in Advanced Packaging and Detector Laboratory). MINIMUM QUALIFICATIONS
Career Center | Boca Raton, Florida USA | Engineering
Production Manager/Engineer NAV-TV located in Boca Raton fl. seeks an experienced Production Manager/Engineer. Ideal candidate will be SMT programmer/operator for pick-and-place equipment in a manufacturing environment, have experience programming,
Career Center | san diego,, California USA | Engineering,Production,Quality Control,Technical Support
SMT Process Engineer, ISO-9001, IPC-600/610/620/7711/7721, J-STD-001, Thermal profiling, Lean manufacturing.
Career Center | kerala, any ware India | Production
i have experience in • Operation of wave soldering and water cleaning machine • Inspection ( Reflow and Post Wave ) • Pre Reflow inspection in SMD • Component forming stuffi
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=5459
Electromigration Behavior of SAC(305) / SnBiAg Mixed Solder Alloy Assemblies 中文 MEMBERS LOGIN Membership Become a Member! Renew Membership About SMTA Ambassadors Benefits Classifications Member Directory Member Directory Corporate Suppliers Corporate Users Consultants List Advertisers Update Your Info
| https://www.wesource.com/lab-equipment/contamination-control-cci-le0579-chemical-fume-hood-id-113024/
Contamination Control CCI LE0579 Chemical Fume Hood ID_113024: World Equipment Source COMPANY PROFILE FINDER'S PROGRAM R1-Surplus Wesource159 CALL US
