Semi-automatic Screwdriver Automatic feeding Smart control Big screw compartment Automatic counting Semi-automatic Screwdriver Main specifications: Product model SZ2800S Product size 410*163*266.5mm Product
Manual push lines provide an economical way to manufacturer a variety of products. Push Lines may be either edge carry or roller conveyor that does not have power. As such, operators perform their designated function and than push the product to the
Electronics Forum | Thu Jul 26 14:55:17 EDT 2001 | mparker
Why not a stink bomb during regular work hours? (If you can get any methyl mercapton, that stuff is very odorific. Smells like baby's barf. A little dab'll do ya!) That way you could gage the complaint ratio as time goes by. Could save you much elbow
Electronics Forum | Wed Jun 26 04:00:30 EDT 2019 | SMTA-David
Thanks, I'll take a look. Something else I found was the Z height for the module was set to 1.7mm but I am picking up the part on the PCB surface which is only 1.0mm from PCB being loaded, therefore the part must have been let got 0.7mm above PCB an
Used SMT Equipment | Conveyors
Dynapace Slide Line IBE SMT Inventory ID : 150109-001 Dynapace Serial Number : 226508-01-02 Vintage : 2009 Details • Overhead Lights • 36" Total Length • 21" Max Board Width • Bin and Document Holders •
Used SMT Equipment | THT Equipment
Spare parts for Universal Radial and Axial through-hole insertion machines Model specifications: (RAD5 6360D, RAD8 6380A, RAD8 XT 6380B, VCD5 6241D, VCD8 6241F, VCD Dual 6292A, SEQ 2596A, SEQ5, SEQ8). UIC Part Number / Part Description 15754 O
Industry News | 2021-12-08 20:33:21.0
Refrigeration compressor is a kind of driven fluid machinery, which promotes low-pressure gas to high-pressure gas and is the heart of refrigeration system. The refrigeration compressor sucks the refrigerant gas of low temperature and low pressure from the suction pipe, then drives the piston to compress the gas through the motor operation, and finally discharges the refrigerant gas with high temperature and high pressure to the exhaust pipe to provide power for the refrigeration cycle, so as to complete a refrigeration cycle: compression → condensation (heat release) → expansion → evaporation (heat absorption) Compressors can be divided into piston compressor, screw compressor, centrifugal compressor, etc.
Industry News | 2020-12-20 23:40:23.0
Easily Installed Excel Cell Emergency Switches Available in 22mm, O25mm and O30mm Mounting Diameters
Parts & Supplies | SMT Equipment
ORIGINAL NEW SMT SPARE PARTS JUKI MTS IF CABLE ASM E94557230A0 Specifications: Brand Name JUKI IF CABLE Part number E94557230A0 Model E94557230A0 Ensure Test in machine confirmation Guarantee 1 month usage for machine JUKI MTS Sell & B
.jpg)
Parts & Supplies | SMT Equipment
03004332-01 Flat Ribbon Cable Set TWIN 03004333-01 Flat Ribbon Cable Set DLM 03004334-03 Flat Ribbon Cable DLM-BE 03004635-02 Vision Control Unit 1 total 03004645-01 COVER Y-MAGNET GUIDE HF 03004647-02 VISION BOARD analog complete 03004676S01 P
Technical Library | 2020-11-24 23:01:04.0
The miniaturization trend is driving industry to adopting low standoff components or components in cavity. The cost reduction pressure is pushing telecommunication industry to combine assembly of components and electromagnetic shield in one single reflow process. As a result, the flux outgassing/drying is getting very difficult for devices due to poor venting channel. This resulted in insufficiently dried/burnt-off flux residue. For a properly formulated flux, the remaining flux activity posed no issue in a dried flux residue for no-clean process. However, when venting channel is blocked, not only solvents remain, but also activators could not be burnt off. The presence of solvents allows mobility of active ingredients and the associated corrosion, thus poses a major threat to the reliability. In this work, a new halogen-free no-clean SnAgCu solder paste, 33-76-1, has been developed. This solder paste exhibited SIR value above the IPC spec 100 MΩ without any dendrite formation, even with a wet flux residue on the comb pattern. The wet flux residue was caused by covering the comb pattern with 10 mm × 10 mm glass slide during reflow and SIR testing in order to mimic the poorly vented low standoff components. The paste 33-76-1 also showed very good SMT assembly performance, including voiding of QFN and HIP resistance. The wetting ability of paste 33-76-1 was very good under nitrogen. For air reflow, 33-76-1 still matched paste C which is widely accepted by industry for air reflow process. The above good performance on both non-corrosivity with wet flux residue and robust SMT process can only be accomplished through a breakthrough in flux technology.
03004332-01 Flat Ribbon Cable Set TWIN 03004333-01 Flat Ribbon Cable Set DLM 03004334-03 Flat Ribbon Cable DLM-BE 03004635-02 Vision Control Unit 1 total 03004645-01 COVER Y-MAGNET GUIDE HF 03004647-02 VISION BOARD analog complete 03004676S01 P
03038908S01 Z-MOTOR WITH PCB 03038979-01 Replacementfilter for F74G-6GN-QP1 5um 03039042-02 REJECT BOX SIPLACE 6x6 03039046S01 COVER Z-LIGHT BARRIER top II 03039078S03 Station Computer HS50 (D1961) 03039080S01 CPU-Bg. SMP16-CPU076
Career Center | Milwaukee, Wisconsin USA | Engineering
Cree Lighting, A company of IDEAL INDUSTRIES, is an LED lighting pioneer known for being first – first to bring LED lighting to the masses, first to deliver no compromise white light, and first to offer a sensor-integrated intelligent lighting
1st Place Machinery Inc. | http://www.firstplacemachinery.com/smt_pcb_pic_place_philipsparts.html
) 4 5322-256-92179 NOZZLE HOLDER, COMPLETE (OLD STYLE) (E) 4 5322-492-71671 SPRING, SHAFT (E) 3 5322-405-91661 LEVER CLAMP (PUSH-IN LOCK HANDLE) (E
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/polymer-processing-systems/products/fluid-coating-systems/premier-die-positioners
, cart/platform mounted, or floor mounted systems Optional angle of attack and roll drive Premier Smart Station features push-button controls with large HMI display screen, eliminating manual adjustments
