New Equipment | Coating Equipment
Cost-effective Solutions for Conformal Coating New cost-effective, automated Conformal Coating System (SimpleCoat TR) with tilt and rotate capability and excellent repeatability for just under $48,000. SimpleCoat basic model without tilt and rotate
Barcodes and Board Traceability Allows automatic process program selection and board traceability, both locally and remotely. Notes Currently supported barcode readers include: Symbol – DS6700, LS2208 Cognex – DM100 Microscan – HS-2, MS-3, MS
Electronics Forum | Mon Oct 24 09:07:58 EDT 2016 | robl
Could you make up your own adaptor cable to connect to your programmer, then fit a small form connector like a Firewire on the edge of the PCB? It should only take up about 7x7mm of real estate as opposed to a 2.54mm 5x2 pin header 12.7 x 5.08, or a
Electronics Forum | Thu Oct 05 21:14:08 EDT 2006 | chrisgriffin
I'm with Chunks on this. In my experience MPM's are very accurate and reliable. There are so many out there because people like them. You can make a program with 2D inspection in about 10 minutes. Things do sometimes break on the 3000's, but not
Used SMT Equipment | Pick and Place/Feeders
Model: CP45F-NEO Mounting speed:14,900CPH(IPC9850) Component recognition range:1005(0402)~□22mmIC 0603(0201) ~ □12mm(option) Placement accuracy:±0.08mm PCB SIZE: 50×30×0.3~460&
Used SMT Equipment | Pick and Place/Feeders
Model: CP45FV-NEO Mounting speed:14,900CPH(IPC9850) Component recognition range:1005(0402)~□32mmIC 0603(0201) ~□42mm(option) Placement accuracy:±0.08mm/CHIP;±0.04mm/CFP PCB SIZE: 50
Industry News | 2020-02-25 12:51:11.0
MIRTEC will exhibit at the SMTA Dallas and Houston Expo & Tech Forums. The Dallas Expo is scheduled to take place Tuesday, March 24, 2020 at the Plano Event Center in Plano, TX, and the Houston Expo will be held Thursday, March 26, 2020 at The Stafford Centre in Stafford, TX.
Industry News | 2003-05-06 09:05:12.0
New Schematic Capture and Simulation Software Delivers Innovative Features and the Industry�s Best Price/Performance
Technical Library | 2013-03-27 23:43:40.0
Vapor phase, once cast to the annals’ of history is making a comeback. Why? Reflow technology is well developed and has served the industry for many years, it is simple and it is consistent. All points are true – when dealing with the centre section of the bell curve. Today’s PCB manufacturers are faced with many designs which no longer fall into that polite category but rather test the process engineering groups with heavier and larger panels, large ground planes located in tricky places, component mass densities which are poorly distributed, ever changing Pb Free alloys and higher process temperatures. All the time the costs for the panels increase, availability of “process trial” boards diminishes and yields are expected to be extremely high with zero scrap rates. The final process in the assembly line has the capacity to secure all the value of the assembly or destroy it. If a panel is poorly soldered due to poor Oven setup or incorrect programming of the profile the recovery of the panel is at best expensive, at worst a loss. For these challenges people are turning to Vapor Phase.
Technical Library | 2023-12-18 21:07:29.0
Selective soldering utilises a nozzle to apply solder to components on the underside of printed circuit boards (PCBs). This nozzle can be moved to either perform dips (depositing solder to a single component) or draws (applying solder to several components in a single movement). The selective soldering methodology thereby allows the process to be tailored to specific joints and allows multiple nozzle types to be used if required on the circuit board. Nozzles can vary by size (internal diameter) and shape (making them suitable for different process types). This is all dictated by board design and process requirements. Selection of the nozzle type is dependent upon the product to be soldered and the desired cycle time. Examples of different nozzle types are shown here. Hand-load selective systems must be programmed with the parameters for multiple solder joints. However, many in-line systems are designed to be modular. This modularity allows for multiple solder stations with different conditions/nozzles to achieve low cycle times. Figure 1 shows the two distinct types of selective soldering systems offered by Pillarhouse International Ltd.
Cost-effective Solutions for Conformal Coating New cost-effective, automated Conformal Coating System (SimpleCoat TR) with tilt and rotate capability and excellent repeatability for just under $48,000. SimpleCoat basic model without tilt and rotate
Training Courses | | | IPC/WHMA-A-620 Specialist (CIS)
The Certified IPC/WHMA-A-620 Specialist (CIS) training focuses on cable and wire harness fabrication and installation.
Training Courses | | | PCB Inspection Courses
The PCB inspection courses focus on improving PCB yield and reliability through validation and detection of defects on electronics assemblies.
Events Calendar | Thu Jul 22 00:00:00 EDT 2021 - Thu Jul 22 00:00:00 EDT 2021 | ,
Webinar: Effective Strategies to Sharpen Your Focus and Concentration
Events Calendar | Wed Mar 01 07:00:00 EST 2017 - Thu Mar 02 11:00:00 EST 2017 | Dallas, Texas USA
Corporate Crisis and Security Forum
Manufacturers Alliance for Productivity and Innovation (MAPI)
Career Center | Rocklin, California USA | Production
General Overview of Position With this new position Parallax aims to improve our USA manufacturing throughput in a time when most companies normally only send work offshore. This raises the standard for requiring efficient use of our Pick and Place
Career Center | Charlotte, North Carolina USA | Accounting/Finance
Financial Analyst � Travel and Expense Will partner with Concur and customize the applications to meet the needs of Solectron worldwide. Will serve as single point of contact on behalf of company with account manager from Concur. Will incorporate
SMTnet Express, September 3, 2015, Subscribers: 23,433, Members: Companies: 14,606, Users: 38,891 Embedded Fibers Enhance Nano-Scale Interconnections V. Desmaris, S. Shafiee, A. Saleem, A. Johansson and P. Marcoux; Smoltek AB While the density
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/asymtek/industries/electronics-assembly-and-packaging?con=t&page=33
manufacturing SMTA Houston Expo & Tech Forum 2016 Nordson ASYMTEK Attend the free technical program and lunch and come see Nordson ASYMTEK at the expo SMTA Dallas Expo
Surface Mount Technology Association (SMTA) | https://www.smta.org/certification/
. The SMTA will issue and mail the certificate within three weeks of the program to applicants who have passed the exam. View a sample question here