Technical Library: siemens and reach (Page 1 of 2)

SMT Placement Machine Nozzle Maintenance and Operation Instructions from KINGSUN

Technical Library | 2023-08-14 09:06:53.0

In the operation of SMT mounter, the process and integrity of the nozzle of the mounter will have a significant impact on the performance of the machine. As one of the important components of the SMT machine, it is necessary for us to carry out daily maintenance and upkeep of the SMT nozzle. To ensure that the suction nozzle of the SMT machine is intact before operation, how should we do a good job of maintaining the suction nozzle of the SMT machine during normal use? KINGSUN technical team analysis operation has the following main points: 1.Wipe the surface of the SMT nozzle with a dust-free cloth. 2.The small aperture nozzle can be passed through with a thin steel wire and then blown with an air gun. 3.The surface of the nozzle should not be soaked with corrosive solution such as alcohol, as this may cause the surface to fall off. 4.HOLDER should use a cotton swab to wipe the cavity and not damage the filter screen. 5.Regular addition of special grease to HOLDER claws. 6.According to production, it is best to regularly maintain and do other maintenance regularly. (* Suitable for Yamaha SMT machine nozzles , JUKI SMT machine nozzles, Samsung SMT machine nozzles, Panasonic SMT machine nozzles, Fuji SMT machine nozzles, Siemens SMT machine nozzles etc.) Regarding the SMT machine nozzle daily maintenance operation instructions, KINGSUN share with you here , hoping to be helpful to you. More information about Products please Contact US at jenny@ksunsmt.com or visit www.ksunsmt.com , thanks.

DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD

Drying and storage recommendation for printed circuit boards

Technical Library | 2024-01-08 18:44:00.0

Printed circuit boards, especially multilayer, flexible and rigid-flexible printed circuit boards, are extremely hygroscopic, i.e. they absorb and bind the moisture in the air. A dried polyimide film, for example, will have reached its moisture saturation level again after just a few hours.

ILFA GmbH

The Characterization and Comparison of Spray Fluxers

Technical Library | 1999-04-26 11:52:34.0

An evaluation of two fluxers, one with a reciprocating ultrasonic head and the other with microjets, was performed using nine independent criteria. The paper describes the methods of testing and the results.

Siemens Process Industries and Drives

Sustainable Product Design and Supplier Material Disclosure

Technical Library | 2016-08-25 17:05:48.0

Sustainable product design and the task of bringing new, earth friendly products to market is a top priority for corporate leaders in the manufacturing industry. By not reaching their compliance and sustainability goals, manufacturers risk loss of market share, fines for non-compliance against regulatory directives and possible damage to their brand. Managing material disclosure information from the supply chain is one of their biggest challenges.

Siemens PLM Software

Benefits and Costs of Overstress Testing (HALT)

Technical Library | 2023-08-14 20:45:11.0

The partnership of Design and Manufacturing is central to the process of bringing a product to market. The impact of problems in either of these stages can increase exponentially if they go unnoticed until after the product reaches the customer. Overstress Test (tests using stresses beyond the design limit of the product) is successful at uncovering such faults in both product design and the manufacturing process and insures the overall robustness of the product. The benefits of Overstress Test include ...

Cisco Systems, Inc.

How to choose printing squeegees and Pressure details affect printing solder paste result

Technical Library | 2022-07-11 09:24:48.0

The change of squeegee pressure has a significant impact on printing. Too small pressure will make the solder paste unable to effectively reach the bottom of the stencil opening and not be well deposited on the pad. Too much pressure will cause tin The paste is printed too thin and can even damage the stencil.

Shenzhen FS equipment CO.,LTD

Reflow Soldering Processes and Troubleshooting: SMT, BGA, CSP and Flip Chip Technologies

Technical Library | 2021-01-03 19:24:52.0

Reflow soldering is the primary method for interconnecting surface mount technology (SMT) applications. Successful implementation of this process depends on whether a low defect rate can be achieved. In general, defects often can be attributed to causes rooted in all three aspects, including materials, processes, and designs. Troubleshooting of reflow soldering requires identification and elimination of root causes. Where correcting these causes may be beyond the reach of manufacturers, further optimizing the other relevant factors becomes the next best option in order to minimize the defect rate.

Indium Corporation

Inkjet-Printed and Paper-Based Electrochemical Sensors

Technical Library | 2018-07-03 12:27:02.0

It is becoming increasingly more important to provide a low-cost point-of-care diagnostic device with the ability to detect and monitor various biological and chemical compounds. Traditional laboratories can be time-consuming and very costly. Through the combination of well-established materials and fabrication methods, it is possible to produce devices that meet the needs of many patients, healthcare and medical professionals, and environmental specialists. Existing research has demonstrated that inkjet-printed and paper-based electrochemical sensors are suitable for this application due to advantages provided by the carefully selected materials and fabrication method. Inkjet printing provides a low cost fabrication method with incredible control over the material deposition process, while paper-based substrates enable pump-free microfluidic devices due to their natural wicking ability. Furthermore, electrochemical sensing is incredibly selective and provides accurate and repeatable quantitative results without expensive measurement equipment. By merging each of these favorable techniques and materials and continuing to innovate, the production of low-cost point-of-care sensors is certainly within reach

Louisiana State University

Jetting Strategies for mBGAs a question of give and take...

Technical Library | 2015-04-02 20:12:58.0

The demands on volume delivery and positioning accuracy for solder paste deposits are increasing as the size and complexity of circuits continue to develop in the electronics industry. According to the iNEMI 2013 placement accuracy for these kinds of components will reach 6 sigma placement accuracy in X and Y of 30 um by 2023.This study attempts to understand the dependencies on piezo actuation pulse profile on jetting deposit quality, especially focused on positioning, satellites and shape. The correlation of deposit diameter and positioning deviation as a function of piezo actuation profile shows that positioning error for deposits increase almost monotonically with decreasing droplet volume irrespective of the piezo-actuation profile. The trends for shape and satellite levels are not as clear and demand further study.

Mycronic AB

1Click SMT Made Successful Installation and Training For Thai Customer!

Technical Library | 2020-04-01 05:52:59.0

Recently, our engineer Peter went to Thailand to provide after-sales support for our customer. In these days, we had installed a SC-900 selective coating line . Moreover, Peter gave patience and meticulous training to their staff, make sure they master the machine usage .Customer and agent are satisfied with our support and give their affirmation to us. SC-900 is a high Performance 4 axis Selective Coating Machine ,which is equipped with high precision servo control system , various valves , CCD system ,material tank weight detecting system etc, which can provide a high efficiency conformal coating process .The maximum coating size can reach 400mm*450mm with SC-900. So far, we've installed several dozen conformal coating line all over the world. It have excellent stability and performance. Check below link to get more info!

1 CLICK SMT TECHNOLOGY CO., Limited

  1 2 Next

siemens and reach searches for Companies, Equipment, Machines, Suppliers & Information