Qualification of boards and assemblies is the comparison of the board or assembly to an industry standard. Specifically, we qualify printed circuit boards to IPC-6012 – Qualification and Performance Specifications for Rigid Printed Boards and
New Equipment | Board Handling - Pallets,Carriers,Fixtures
Green Wave Solder Pallet Materials ESD composite material substitutes for CDM 68950 Overview 1, KT series wave solder pallet material is reinforced glass-filler combined with high temperature and static dissipative epoxy resin. &nb
Electronics Forum | Tue Dec 28 03:59:06 EST 2010 | riscy00
I'm investigating heat transfer by 1st order approximation between PCB and ambient air via encapsulate material (epoxy or gel or silicone), they have thermal conductivity of 0.2W/C but it hard to find specific heat capacity and density. Has anyone
Electronics Forum | Fri Jun 06 16:11:25 EDT 2003 | RF Lurker
I understand that there may not be a lot of material on this, as most threads I've seen discourage doing it. It goes against DFM to do it. But I wish to use a large copper area instead of heat sink and thermal epoxy to cool a regulator. But I can'
Industry News | 2024-03-01 16:23:48.0
The Branford Group ("Branford"), a leader in asset liquidation and valuation services, in partnership with Joseph Finn and New Mill Capital, will be hosting a major public auction event to sell assets from the complete facility closure of NexGen's East Syracuse, NY manufacturing facility. This multi-million-dollar investment will be available for bidding via online auction. Bidding will open on March 11th at 8:00am (ET) and will begin to close on March 13th at 11:00 am (ET).
Industry News | 2003-08-27 10:58:00.0
Lead free solders and embedded passives headline professional development schedule at the 2003 IPC Annual Meeting
Technical Library | 2019-11-12 02:09:22.0
Thermal shock test chamber can be used for testing the chemical change or physical damage on composite materials caused by the thermal expansion and contraction of the sample in the shortest time,which is subjected to extremely and continuous high and low temperature environment.so how to check the temperature recovery time of this chamber? Normally we take following steps to inspect the temepratuire recovering time: 1.Install the temperature sensor at the specified position, and adjust the temperature controller of hot zone and cold zone to the required nominal temperature respectively. 2.The temperature increases and reduces respectively,30min after temperature in two zones reach stable status,record temperature value of the measuring point,pls set the temperature value of two zones to be required nominal temperature. 3.The temperature shock test chamber automatically places the inspected load into theh ot zone,select the corresponding retention time according to regulated standard. 4.Set the transfer time,then the inspection load is transferred from hot zone to cold zone, and the temperature of the measuring point is observed and recorded, and then the reverse conversion of the load from cold zone to hot zone is carried out according to the same method, and the temperature of the measuring point is observed and recorded. www.climatechambers.com
Technical Library | 2017-05-04 17:35:01.0
Most of today's printed circuit board base materials are anisotropic and it is not possible to use a simple method to measure thermal conductivity along the different axis, especially when a good accuracy is expected. Few base material suppliers' datasheet show X, Y and Z thermal conductivities. In most cases, a single value is given, moreover determined with a generic methodology, and not necessarily adapted to the reality of glass-reinforced composites with a strong anisotropy.After reminding of the fundamentals in thermal science, this paper gives an overview of the state-of the art in terms of thermal conductivity measurement on PCB base materials, and some typical values. It finally proposes an innovative method called transient fin method, and associated test sample, to perform reliable and consistent in plane thermal conductivity measurement on anisotropic PCB base materials.
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
The LPKF ProtoFlow S reflow oven, with lead free capability, has significant advantages over previous models and rich features including a PC control software package. Learn more: http://www.lpkf.com/products/rapid-pcb-prototyping/smd-assembly/solder
SMTnet Express, May 4, 2017, Subscribers: 30,444, Companies: 10,591, Users: 23,216 Development of a Consistent and Reliable Thermal Conductivity Measurement Method, Adapted to Typical Composite Materials Used in the PCB Industry Francois
ORION Industries | http://orionindustries.com/pdfs/thermal.pdf
. Sil-Pad , Gap Pad, and Q-Pad are registered trademarks of The Bergquist Company. One Orion Park Drive, Ayer, MA 01432 • Phone: 978-772-6000 • Fax: 978-772-0021 • E-mail: info@orionind.com • www.orionindustries.com ORION INDUSTRIES INCORPORATED GAP PADS Material Thickness Range Thermal Conductivity Gap Pad V0 Soft
Imagineering, Inc. | https://www.pcbnet.com/blog/the-importance-of-thermal-management-in-pcb-manufacturing/
The Importance of Thermal Management in PCB Manufacturing | Imagineering, Inc. Skip to main content Resources Support Contact Us FAQs Live Chat My Account 847-806-0003 Menu PCB Capabilities Fabrication Technology Roadmap Materials Available HDI Tolerances Certifications
