Electronics Forum: quad 4c com (Page 2 of 43)

quad 4c

Electronics Forum | Mon Nov 18 12:07:02 EST 2002 | smckee

It would have to be really CHEAP! I ran one a few years ago, had 3 4C's gained together. Always had problem with the software and it was a high maintenance machine. Never had such problems with Mydata, Phillips or Zevatech. Also, it seemed I alwa

quad 4c

Electronics Forum | Mon Nov 25 16:10:27 EST 2002 | btaylor

I have run the 4Cs for over 8 years it has been a good little machine. We use it for placing 10 mil pitch flip chips. I buy the yearly insurance through Tyco every year.

quad 4c

Electronics Forum | Fri Nov 29 08:36:07 EST 2002 | Jeff Park

They have there strong points and weak ones. I have worked with them for the last 5 years and have seen some flakey problems (Cables, feeders, encoders) that will cause you some down time but if you get a good price on a system it might be worth it.

quad 4c

Electronics Forum | Wed Nov 27 18:10:41 EST 2002 | andrewbrook

Quad4C's have their moments. If the price is right and you are aware of the machines limitations then you will be satisfied. The placement rate is slow, 1.2 seconds/chip. Don't buy any Quad if it has the CyberOptics Laser unit, the Quadalign unit is

quad 4c

Electronics Forum | Mon Nov 18 11:14:57 EST 2002 | bpan

Very good machine. Dont know about Claude but sounds like he doesnt know the machine too well. Be careful if you buy it because Tyco's Parts support for the machine are terrible. For ex. Tried to buy a sensor for the lifters on our transport and they

quad 4c

Electronics Forum | Thu Nov 21 11:35:47 EST 2002 | hannahsd

We had several 4c's before we put them out to pasture. From my experience they are easy to make program adjustments, but like the previous person responded the auto programmer did not work for us. We had laser coplanarity check as an addition to th

quad 4c

Electronics Forum | Wed Nov 27 09:51:08 EST 2002 | Claude_Couture

I have worked with 4c's for two years. The feeders are "tinker toys" with a mechanism that slips, so the pick-up has to be adjusted several times as the reel is used, especially with 13" reels. The worm gear was plastic on the steel shaft of the moto

quad 4c autoprogram

Electronics Forum | Mon Mar 06 20:50:47 EST 2017 | arachid

Hi, I get a old pick and place machine quad 4c. I don't have manuel for autoprogram. i think version 4.4. anybody know where I can find it? Thanks

quad 4c automatic paste dispencer

Electronics Forum | Sat Jun 17 04:07:49 EDT 2017 | arachid

Hi, i have a quad 4c, i like to know is it posible to add an automatic paste dispencer for this pick and place machine? if yes every body can helpme to find one and find how to install it? Thanks

quad 4c automatic paste dispencer

Electronics Forum | Mon Jun 19 11:53:22 EDT 2017 | westshoredesign

Out of curiosity, are these compatible with all C series models?


quad 4c com searches for Companies, Equipment, Machines, Suppliers & Information

Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

Best Reflow Oven
Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

World's Best Reflow Oven Customizable for Unique Applications
Global manufacturing solutions provider

Wave Soldering 101 Training Course