Electronics Forum | Wed Jul 04 10:40:51 EDT 2001 | nifhail
I have thousands of old datecode PCBs which has an Entek and HASL finished. Entek PCBs are about 6 � 1.5 years old and HASL boards are at 1 - 2 years old. To make it worse, some of them came in the loose form, no vacuum seal� nothin�. As for the HA
Electronics Forum | Wed Sep 08 17:31:58 EDT 1999 | Earl Moon
| I am wave soldering a single sided through hole PCB array with (6) .040" round diameter pins that sit .5" off the PCB, and .080" apart. The problem being experienced is that solderballs are appearing on the end of the pins. I have tried decreasin
Electronics Forum | Fri May 28 07:37:52 EDT 1999 | Steve Cheung
Yes l know this problem keeps cropping up on the forum but l've missed some of the follow-ups. Our problem is that the lifting only occurs on 3% of production so actually detecting an improvement is difficult. We're actually having to inspect 144 p
Electronics Forum | Thu Apr 15 14:56:43 EDT 1999 | Dave F
| Can anyone suggest or identifiy standards which tabulate the following: | | Conductor width, cross sectional and area conductor thickness for PCB's carrying up to 70 Amps? | Barry: Check: 1 Printed Circuits Handbook (Clyde F. Coombs) 2 Microel
Electronics Forum | Sat Jun 13 11:00:21 EDT 1998 | Earl Moon
| We are very concerned about outgassing in wavesoldering. | If anyone knows how to use properly well pcb's before soldering in order to avoid this problem please let me know. I have this problem in FR4 large double sided pcb's. My soldering line is
Electronics Forum | Wed Jun 10 13:42:22 EDT 1998 | FRANK
| We're running into problems with board damage (broken traces, solder shorts) due to pliers and other bizarre tools being used for depanelization. I need some sort of fixture for this. A delrin plate with a slot cut to the correct depth and width mi
Electronics Forum | Mon Apr 29 05:25:13 EDT 2002 | ianchan
Hi, we do Sn plated I/O pinning insertion into Ni/Au thru' holes. no problems here so far, as we cater for the "interference" (fit-allowances) of the I/O pin into the thru' diameter, via improved PCB thru' hole designs. before this cater/considerati
Electronics Forum | Thu Feb 06 14:47:50 EST 2003 | MA/NY DDave
Hi "some customers/designers want to have via holes to be present in the PCB pad, due to some belief that it helps in heat dissipation. " As I think about this I don't know exactly why they would be concerned. I can imagine in some exotic products
Electronics Forum | Mon Apr 12 07:44:50 EDT 2004 | wgaffubar
Former company we use to replace No Lead BGA's by using dot dispense to apply eutectic solder to pad with same volume the stencil printer. Current company process removes bad BGA, wicks off solder paste then Hot Gas Reflows new No Lead BGA to bare pa
Electronics Forum | Fri Jul 16 20:17:15 EDT 2004 | cisridn
Hello! I am an Electrical Technician with Filtronic Comtek. I am responsible for all of the Engineering changes and rework done to prototype and pilot run PCB's. My current rework equipment includes: Soldering irons, heat gun, and hot plate. Consid
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
