Electronics Forum | Fri Oct 03 09:00:18 EDT 2003 | davef
EIA standard packages have a variety of L/W proportions. EIA||Dimension mm (LXW)||Proportion (L/W) 0201||0.6X0.3||2 0202||0.5X0.5||1 0303||0.8X0.8||1 0402||1.0X0.5||2 0504||1.25X1.0||1.25 ||1.4X1.4||1 0603||1.6X0.8||2 0805||2.0X1.25||1.6 1111||2.8X2
Electronics Forum | Thu Sep 08 09:41:51 EDT 2005 | PWH
If you do find your camera is bad, I think they are relatively easy to replace if you get a new one. I have done a 1.0 and 4.0 GSM camera replacements but not a PEC as of yet. If it's like the 1.0 and 2.6 and 4.0's, likely it is not tough but will
Electronics Forum | Sun May 18 19:04:54 EDT 2008 | jmelson
OK, here's a sample component file : 1 0.1uF 0.00 1 24 1.00K 0.00 1 22 10.0K 0.00 1 3 1000pF 0.00 1 3 .001uF 0.00 1 25 1.0uF 0.00 1 2 100pF 0.00 1 30 10M 0.00
Electronics Forum | Thu May 31 21:45:48 EDT 2012 | davef
rsthompson ... if you're talking about bare boards IPC-5701, Users Guide for Cleanliness of Unpopulated PBC, Table 8 ||Bare board final surface finish Ions||Hot air solder level||OSP over copper||Gold over nickel Chloride||0.75 ug/cm^2||0.75 ug/cm^2
Electronics Forum | Mon Jan 14 12:28:06 EST 2008 | swag
We are in North Western U.S. I like 2.6 better (for our mix of builds, anyway). 1.0 works great on PTF parts such as fine pitch QFP's but I don't like it for chips. It's too picky and we wind up forcing parts to the 4.0. We have another GSM dual
Electronics Forum | Thu Mar 19 21:09:09 EDT 2020 | sarason
Have you tried PCBSynergy? https://pcbsynergy.com then team it with Programming by Ealead https://ealead-e.ucoz.com/load/eps/1-1-0-1 sarason
Electronics Forum | Tue Jun 23 22:14:16 EDT 2020 | kumarb
Hi. Guessing that you are operational by now? If not, consider to use BGA definition and use the editor to define where the bottom side pads are or are not. Just our 2 bits input. The Assembleon X / Yamaha units are quite flexible - using an electron
Electronics Forum | Tue Feb 22 23:52:06 EST 2000 | Finepitch Services
Jax, I appreciate your opinion and no one is right or wrong during such information sharing. Please consider that we all inherit a system and keeping it in the same way is the choice in most cases. Also, "keeping the mm across the house" is not gi
Electronics Forum | Mon Nov 04 16:54:13 EST 2002 | pjc
For me it was the 1.0mm nozzle, if we're talking mini-MELF here. Also, slowing the turret speed helps. Had mine at 30%. Results vary if placing on paste vs. glue. Paste is better. Still, the std. 1.0mm nozzle is where near as good as with the MELF no
Electronics Forum | Thu Jul 06 23:59:11 EDT 2017 | heros_electronics
We got an inquiry from US that requires high volume 8 layer 1.0mm PCB, OSP + selective ENIG surface, 5 groups impedance control, and stacked vias. These requirements are common, but there is 2/2mil lines in inner layers. It's said that this order was