Electronics Forum: 2mm (Page 2 of 25)

Quad Feeder Programming - ThinPRO 2mm Index

Electronics Forum | Thu May 19 12:49:14 EDT 2016 | rx8pilot

Tom Nisbet from PPM contacted me on the phone yesterday to help me understand the various feeder options for small parts. Fantastic surprise phone call that was inspired by this thread. I explained my business strategy and financial restrictions an

Quad Feeder Programming - ThinPRO 2mm Index

Electronics Forum | Tue May 17 13:10:50 EDT 2016 | rx8pilot

Thank you Bobpan - I tried that sequence but instead of LED's flashing - they were solid and it remains in 4mm mode. After looking closer at the feeders, it appears there are 'SlimPRO' and 'ThinPRO' versions. The ThinPRO version is what PPM manufactu

Is anyone placeing a 2x20 2mm low profile SMT header?

Electronics Forum | Tue Aug 31 12:53:15 EDT 1999 | jseagle

Just what the subject says. If you are what type of machine are you using, is it mechanical or vision centered? What is the reject rate? Thanks for any help. James

What is the acceptable annular ring size per IPC for 2mm 2x5 header ??

Electronics Forum | Fri Jun 06 13:03:01 EDT 2014 | asksmt

Hi All, i have footprint 2X5 RA HEADER 2MM spacing in design. I am using about 9 mils of annular ring on top side and about 12 mils of annular ring on bottom side. refer picture attached. we are having solder short issues during wave solder so was

Flux dip or solder print for CSP

Electronics Forum | Wed Feb 01 02:21:26 EST 2017 | rob

80 micrometres (0.08mm) or 80 mil (2mm)? Smallest I've seen reliably printed is around 0.2mm x 0.4mm (01005 pad) and 0.2mm x 0.2mm CSP pad, not seen anything dispensed below 0.35ish, but we are not cutting edge.

Problems encountered in mounting 01005 components on 0.2mm PCB

Electronics Forum | Tue Oct 07 09:40:44 EDT 2008 | john_smith

Dear, Flexkhushi Do you mean 2 mm thick board or .2 mm board. If you are talking .2mm then you are refering to a flex circuit correct? What equipment will you be using to place the 01005 component? I

2MM pitch tape

Electronics Forum | Wed Jan 08 14:18:34 EST 2003 | soupatech

I have run across a resistor array whose tape has a 2mm pitch. Is there a way to modify a Fuji CP3 8x4 feeder to make it 8x2? Or do I need to purchace new feeders?

Problems encountered in mounting 01005 components on 0.2mm PCB

Electronics Forum | Fri Oct 03 01:01:09 EDT 2008 | khushi

Dear All, I would like to know that what are the problems which will be encountered while mounting 01005 components & BGA's on the PCB for thickness 0.2mm and what will be the processes involved in mounting the components.

Temperature Profile for 0.2mm Thick ENIG Flex PCB

Electronics Forum | Thu Jan 30 10:12:00 EST 2020 | emeto

More detail Jinesh. Profile, datasheet of the part, stencil design, PCB finish, soldering material. Initially I am assuming you use pallet to reflow 0.2mm thick board.

Problems encountered in mounting 01005 components on 0.2mm PCB

Electronics Forum | Wed Oct 08 00:28:31 EDT 2008 | khushi

Dear, Flexkhushi > Do you mean 2 mm thick board or .2 mm board. If > you are talking .2mm then you are refering to a > flex circuit correct? What equipment will you be > using to place the 01005 component? I am not sure > if you can even place a


2mm searches for Companies, Equipment, Machines, Suppliers & Information