Electronics Forum | Wed Jul 20 18:08:35 EDT 2016 | freakshow
any help is much appreciated, I keep getting a random shutdown, sometimes a few minutes sometimes after a few hours. "emergency Stop, Please check the stop button" of course no one is touching the stop button and the button does not seem to be faulty
Electronics Forum | Fri Mar 15 21:20:18 EDT 2024 | compit
Check out Yamaha - also old. A large number of parts (the same machines under the Assembleon, Philips brand), cheap feeders, many parts suppliers. Models from 2 to 16 heads, e.g. Emerald-X can accommodate 84 INDEPENDENT 8 mm feeders.
Electronics Forum | Tue Aug 11 17:36:44 EDT 2009 | dyoungquist
You are looking for a complete SMT assembly line plus possible X-Ray inspection and rework equipment. The 3 components of the SMT line are stencil printer, pick-n-place machine and reflow oven. How small are your components? 0603? 0402? What is the
Electronics Forum | Tue Mar 19 14:57:48 EDT 2024 | spoiltforchoice
I hadn't suggested the IINEO's because as a step up from Neoden's its a huge leap in price and perhaps around twice the price of the AM100, that gap would narrow as you purchased even more feeders. If you have a big product mix or are a small batch
Electronics Forum | Mon Aug 10 15:15:17 EDT 2009 | indity
I have very little knowledge of pick and place machines or assembly, and was hoping someone could give me some advice of where to start looking. I do learn quickly so I am not afraid of challenges or learning through mistakes. I need to produce abou
Electronics Forum | Tue Mar 19 11:54:56 EDT 2024 | tommy_magyar
Hi there, I've been happy with the iiNeo and iiNeo+ from Europlacer, both have the capacity of 8*33 8mm feeders (264 slots in total). It can build boards up to 505*360 mm (our biggest PCBA, maybe it can do bigger one too). 6 and 12 monthly services
Electronics Forum | Wed May 09 10:39:03 EDT 2001 | davef
The two first level cuts at comparing placement machines are: * Placement rate * Range of component capabilities This boils-down approximately to machine price. Virtually, everyone's feeders are priced similarly. Go to "Circuits Assembly" magazine
Electronics Forum | Wed Jun 11 11:50:50 EDT 2008 | mmjm_1099
Mydata is a large footprint. I would personally look into AIM, XP242, or even universals or panasonics. I would make sure to watch auctions or check used market. We just purchased a XP242 not long ago from auction for about half the proce of a new on
Electronics Forum | Thu May 10 02:57:03 EDT 2001 | kjellman
Hi, Why not have a look at Philips/Assembl�on, their ACM machine is quite nice. It may also bring you down to Flip Chip, 0201 some through hole and odd form placement. Nice options like bulk feeding, coplanarity tests, fluxing for FC, prom feeders (
Electronics Forum | Sun Aug 26 12:40:59 EDT 2001 | stefwitt
I would like to enter the discussion by tossing some numbers in. First of all I don�t like the 3 Sigma value. 3 Sigma are 2000 defects per mio. if I remember correctly. This means, if you have 200 components on the board, then every 10 boards have on
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830