Full Site - : dek 265 front squeegee error (Page 3 of 4)

DEK 265GSX squeegee travel distance

Electronics Forum | Fri Jun 17 10:59:22 EDT 2011 | beta

yes there is - I think it is called front print limit & rear print limit

DEK 265GSX squeegee travel distance

Electronics Forum | Wed Jun 29 15:42:19 EDT 2011 | dekhead

Yes it is "Print Front Limit" and "Print Rear Limit". Negative value extends the stroke, Depends on software version how useful it will be, as there are differing limits on how much you can extend the stroke. http://www.dekhead.com

DEK 265 pneumatic power down error

Electronics Forum | Thu Jul 30 22:48:17 EDT 2020 | dekhead

MM (MultiMove) cards are in the M19, Motor Control, crate (located front of machine, right side). MM's are the larger cards located on the far right side; X11, X12 and X13 slots (X11 slot is only used in Infinity, empty slot on Horizon / ELA).

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Thu Nov 07 16:02:06 EST 2019 | kylehunter

OK, got a lot of information today doing some testing.. Version number:- 07 SP11 (985 B02) Released Dec 8 2006 I did the tool(less) calibration of the squeegee height, which worked fine, no error. Did a test print, as you can see from the image, t

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Sat Nov 09 19:37:52 EST 2019 | kylehunter

> the issue is the calibration. What you set it for > has to match what it actually reads or you get > the error screen at the end of every pass. If > you go into the maintenance menu ( using the key > next to the system button )

Re: DEK 265 GSX PRINTER

Electronics Forum | Thu Jul 16 16:56:02 EDT 1998 | Doug Nebel

| Howdy 2, | I am using my first DEK GSX PRINTER. Looks and acts good so far. Who know what - good, bad, or in between? Just want to get the facts from those who know. | Earl Moon We have had our 265 GSX a little over 2 years. Print quality has bee

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Thu Aug 27 03:19:21 EDT 2020 | dekhead

Have you done Squeegee Heights calibration? (no tools required) Does it complete cal routine without error? Does pressure compensate on next print, with corresponding squeegee, following acknowledgement of pressure error? The readings calibration, ge

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Thu Aug 27 14:32:34 EDT 2020 | dekhead

Following a pressure error, if continue is pressed, the next print with THE CORRESPONDING squeegee should attempt to compensate by increase or decrease in pressure (as appropriate)... Is it: 1)Not changing at all? 2)Over compensating? 3)Under compens

DEK HORIZON 265 Squeege Pressure question

Electronics Forum | Sat Nov 09 19:35:25 EST 2019 | richardcargill

the issue is the calibration. What you set it for has to match what it actually reads or you get the error screen at the end of every pass. If you go into the maintenance menu ( using the key next to the system button ) you can check that the pressu

DEK 265 GSX - problem since belt change

Electronics Forum | Thu Oct 29 13:55:57 EDT 2015 | edgeflex

Hi, Since we change the small best of the head carriage, the head is not going to the right positions (paste/front/rear). I could not even make a pressure test. Anyway I don't have any error message. Does somebody knows something about this and ho


dek 265 front squeegee error searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

Smt Feeder repair service centers in Europe, North, South America
Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
Best SMT Reflow Oven

High Throughput Reflow Oven
2024 Eptac IPC Certification Training Schedule

Training online, at your facility, or at one of our worldwide training centers"
Assembly Automation Technology

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...