Electronics Forum | Mon Nov 30 20:32:07 EST 1998 | Dave F
| We are in the process of assessing some medium volume, stand alone SMT Placement systems. Does anyone have any experience with :- | | 1) Europlacer (Specifically the Progress 6 or EP600) | 2) Intelliplace (DHM-120 or SHM-120) | | I have searched
Electronics Forum | Sat Oct 21 21:39:43 EDT 2006 | Mats
"Surface Mount Techniques has approximately 98 percent of the world market share of large Panel Stencil Printers". It sounds a little bit strange to me, especially since I work for one of the companys listed in their advertisement and it is definite
Electronics Forum | Tue Dec 11 12:15:36 EST 2007 | swag
We just got a contract to build a board with 1400+ SMT placements. This thing is 16" x 12" and the PCB thickness is 0.142". Dead center is a 580+ pin BGA that costs about $600. I'm a bit intimidated... I've done lots of mole profiling on BGA's bu
Electronics Forum | Wed Jun 04 10:51:28 EDT 2014 | clydestrum
Well, we cannot make the cuts any deeper as then we would incur a significant amount of "bowing" at SMT placement/reflow. -Has anyone ever heard of changes in material/laminate makeup that causes this? A sort-of stronger, or more flexible tensile st
Electronics Forum | Tue Feb 01 16:56:46 EST 2022 | rstellema
Hello all, I have a couple of old FUJI CP-6 SMT placement machines that are operating with very old PCMCIA Flash Memory cards. I would like to insure that I have back-ups should the memory cards fail. I assume that I would need a support USB reader/w
Electronics Forum | Tue Feb 24 10:44:19 EST 2015 | markhoch
We're a Tier-1 Automotive Supplier, manufacturing here in the Good Ole U S of A, and I'm in the processing of putting together our newest SMT Line. This new line will be a dual lane SMT Line. I've been in the industry a long time, and have put togeth
Electronics Forum | Mon Aug 02 14:39:35 EDT 2004 | Vahid
Where can I get a document to describe BIC SMT process (paste, printing, placement machines, ovens, X-Rays, Wave soldering, ICT, and depanelization)? Thanks.
Electronics Forum | Fri Dec 03 18:01:56 EST 1999 | M Cox
Usually the alignment problem comes from pad design. The ground pad (largest) is too small. If that is the case (and even if it isn't) try placing a dot of SMT adhesive before placement (it will cure before reflow and hold the part in place). Goo
Electronics Forum | Tue Mar 30 22:43:36 EST 1999 | dean
| Does anyone know of a contract manufacturing house that can guarantee smt component placement and can verify placement of +/-.015? | | Thanks in advance | Question: mm, inches, or mils? I can do it. However, what is your reliability level? 9
Electronics Forum | Mon Oct 06 14:10:55 EDT 2008 | chineechooze
0.001969" You say that 0.008" of "slop" is un-doable; hence, the reasons for our failures. Any basis for that statement? Are rated accuracies from placement equipment manufacturers typically "exgaggerated?" 2. On PCB Fab side of things, what is
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, China
Phone: 0755-33578694