See Your 2024 IPC Certification Training Schedule for Eptac

11169 parts results

Electronics Forum: parts (Page 250 of 1117)

paper vs emboss (& zig zag placement)

Electronics Forum | Sun Dec 09 11:58:34 EST 2012 | ericrr

Is BOC, Beginning Of Cycle? If it is how boring, The real root of the problem is, some of the parts are not put on the correct place, some of the misplaced parts wobble over on the bubble of solder going through the oven, but some been so light st

In need of Maxim IC DS2710G+

Electronics Forum | Fri Nov 16 17:49:07 EST 2012 | davef

Services, Parts, Distributors, Hard to find parts * SolTec Electronics soltecelectronics.com * Cross Components crosscomponents.com * Farnell / Electronic Component Distributors farnell.com * TTI Inc ttiinc.com * SearchlightTech searchlighttech.com *

Multiple reflows

Electronics Forum | Fri Feb 01 14:49:52 EST 2013 | emeto

Thank you guys. You keep adding valuable information here. I think we will try to stick with the 3 times reflow(if we count the BGA repair as 2 reflows). However sometimes we will run the board second time through the oven(just flux the suspect part

Quad Feeders performance improvement

Electronics Forum | Tue Feb 12 08:42:56 EST 2013 | bobpan

I hope you realize that you can pocket position the part so that it is in the center of the beam on the feeder. To do this.... 1. press both buttons (light go out) 2. press rear button 3 times 3. Then use front button to position part 4. The press re

AOI False Calls

Electronics Forum | Wed Feb 20 10:26:56 EST 2013 | wbailey

I am getting a lot of false calls on our AOI(YTV F1)on low contrast part markings like brown-on-yellow tantalum capacitors and etched oscillators, and on lead banks where the pcb has the part outlined in silkscreen. We are contract and cannot change

Tape not pulling back on components causes machine to stop

Electronics Forum | Thu Mar 14 10:49:44 EDT 2013 | babe7362000

Have others seen a higher rate of machine downtime due to the cover tape on parts not pulling back properly. We have the same problem on the Jukis and Quads. About every 3 minutes the machine stops and the operator has to pull the tape back. And in

SOD 923

Electronics Forum | Mon Mar 25 13:18:05 EDT 2013 | emeto

Hello, I have an issue with SOD 923 out of the oven. The part looks grainy, doesn't show a good wetting and looks like it has to be touched up. Everything on the board looks beautiful except this part. I tried with the profile, I checked the pad des

Mydata (TP9-2U) problem

Electronics Forum | Tue May 07 16:36:04 EDT 2013 | shankar2013

Actually thinking of LX14, but for now I need to solve this problem. We have replaced centering jaws, the steel belts for regular maintenance. I don't think there is anything binding. The strangest thing is every time it shuts down it is right at the

nozzle cleaning GSM

Electronics Forum | Mon May 20 15:19:50 EDT 2013 | smtventasmex

i been trying to do that with a lot of my customers but they can not clean that well it works for just one time but you have to remember than this parts are platic, and will have some damages, i can sell to you quality nozzles at the best price on th

MyData DPak not placing

Electronics Forum | Fri Jul 26 11:20:33 EDT 2013 | gnus

Hi all, I'm having issues placing 7 pin DPak packages. I'm using mechanical centering with four centering phases (one for each orientation). Tool used is A24S. Machine picks up the part but will reject it when centering the part. I have measured all

250