Full Site - : one (Page 1 of 3149)

Frost & Sullivan Lauds Heller Industries' Exceptional Growth Borne of its Advanced SMT Reflow Soldering Equipment for Industry 4.0

Industry News | 2016-06-22 15:33:28.0

Based on its recent analysis of the surface mount technology (SMT) reflow soldering equipment market, Frost & Sullivan recognizes Heller Industries, Inc. with the 2016 Global Frost & Sullivan Award for Growth Excellence Leadership. Heller Industries has made remarkable improvements to its product and technology portfolios over the last 10 years to emerge a top participant in the SMT reflow soldering equipment market.

Heller Industries Inc.

Dam and Fill Dispensing for Medical

Technical Library | 2023-08-16 18:02:27.0

One of our customers in the medical industry requested dam and fill application testing on a Kapton substrate. The material needed to be non-conductive for dispensing around electrical components, acting as structural support. Ultimately the product will be folded, therefore the footprint had to be small.

GPD Global

Solder Mask Dispensing For Electronics and Aerostructures

Technical Library | 2023-08-16 18:09:06.0

One of our customers involved with Electronics and Aerostructures requested a test to dispense Techspray Wondermask 2204 solder mask. The dispensing locations include large and small screw holes, single through-hole vias, and connector locations consisting of multiple through-hole vias. The process needed to run quickly and reliably.

GPD Global

Underfill Dispensing For Aerospace Military And Defense

Technical Library | 2023-08-16 18:20:44.0

One of our defense customers planned to dispense underfill material for small and large die, using Hysol FP4545FC epoxy encapsulant. This process dissipates stress on solder joints and prevents cracking and fracturing between the bottom of the die and the surface of the substrate.

GPD Global

Masking and Underfill Dispensing for Medical Device

Technical Library | 2023-08-16 18:42:25.0

In one of our medical applications projects, the customer wanted to dispense a mask to protect gold leads and an underfill on a silicon substrate with a clear test die. The substrates were Dymax X-499-91-C for Masking and Epoxibond-106M-1 for Underfill Dispensing

GPD Global

LED Encapsulation for Consumer Products

Technical Library | 2023-08-16 18:13:53.0

In one of our Consumer Electronics projects, a smart lighting company wished to dispense silicone-based LED encapsulation material for two different product sizes. The larger product had a 9mm circular dam which required silicone dispensing flush with the top of the dam. The smaller product had a 1mm LED die that required only the top to be encapsulated. The material consisted of two parts which were mixed by weight in a 1:1 ratio. A phosphor powder was added totaling 10% of the overall weight. The phosphor required agitation to remain suspended.

GPD Global

Thermal Interface Material (TIM) Dispensing For Consumer Products

Technical Library | 2023-08-16 18:25:16.0

In one of our Consumer Electronics projects, a leader of networking technologies requested to test dispensing performance of a thermally conductive material, Fujipoly Sarcon SPG-50A. This material improves heat dissipation for higher frequency applications and reduces the negative effects of thermal resistance under heat, cold, humid, and thermal shock conditions. The customer's goal was to dispense a 1mm diameter dot with acceptable speed and consistency.

GPD Global

Staking/Epoxy Adhesive Dispensing for Aerospace

Technical Library | 2023-08-16 18:48:50.0

One of our aerospace customers was looking to automate a few manual operations and asked for suggestions. This customer specializes in assemblies for inflight connectivity for commercial airlines and low orbit satellites. The dispensing process included the application of bonding to the sides of large and small components (4-axis) and the ability to cope with the changing viscosity during processing. The material used was EC-2216 B/A Two Part Epoxy and the largest board size was 12"x10"

GPD Global

Lead Former for Bulk or Loose RADIAL Components (CF-10)

Lead Former for Bulk or Loose RADIAL Components (CF-10)

New Equipment | Lead Forming

Form & Cut 2-, 3-, 4-, 5-, and 7-leaded Radial Components Capable of forming loose radial components at rates up to 5,000 parts per hour with a variable speed motor. Feed components by hand or with tubes (TO-220s) Reduce setup time with quick ch

GPD Global

Precision Lead Former for Taped RADIAL Components (CF-9)

Precision Lead Former for Taped RADIAL Components (CF-9)

New Equipment | Lead Forming

The CF-9 Radial Lead Former forms and cuts 2- and 3-leaded taped radial components such as TO-92s, capacitors, transistors, LEDs, etc. - precisely and repeatedly, in standard and special forms. This machine is capable of forming and cutting up to 25

GPD Global


one searches for Companies, Equipment, Machines, Suppliers & Information