Electronics Forum | Fri Dec 01 00:37:20 EST 2000 | arminski...aka..Dreamsniper
I have a proto-type PCB with a 48-Pin Fine Pitch TSOP (0.5mm pitch) with a dimension of 19mm L x 11.50mm W x 1.10 Thickness. They are at the bottomside of the PCB and I need to wave solder the board. There are 8 of them at the bottom side. Are they o
Electronics Forum | Fri Jul 16 20:17:15 EDT 2004 | cisridn
Hello! I am an Electrical Technician with Filtronic Comtek. I am responsible for all of the Engineering changes and rework done to prototype and pilot run PCB's. My current rework equipment includes: Soldering irons, heat gun, and hot plate. Consid
Electronics Forum | Sun Apr 03 10:07:40 EDT 2005 | davef
In 2001, IVF evaluated the reliability of IBM CBGA and CCGA, i.e. packages with "hard" balls and columns, in space applications for the European Space Agency. One clear result was that amount of solder paste printed on the solder lands is very critic
Electronics Forum | Fri Jan 16 07:06:47 EST 2004 | Mika
Component manufacturer often have recommendation for pad layout and process setup. This should be used as a guideline to help You to set up the process. Exactly what type of component is this, uBGA? We populate 64 I/O uBGA's on our pcb's with 0.3 mm
Electronics Forum | Wed Jun 02 09:55:31 EDT 1999 | Jason Gregory
Hello Dan, I have recently started using polyimide, but not for the standard uses. I designed a pallet for holding small, thin (about .0018" thick) RF boards that were being reflowed inside their aluminum housings. They were screwed down to prevent w
Electronics Forum | Wed Jun 03 13:56:09 EDT 2009 | mika
less total area of voids, which mean a much more strength in the joint and much easier to solder such a cooling pad grounded via vias, with this approach! The same goes for big cooling pads of let say Power transistors without any via etc. Always re
Electronics Forum | Thu Aug 24 15:37:50 EDT 2006 | Chunks
Hi Any, This is from an earlies thread "Solder Ball After Reflow Process". Date: August 16, 2006 01:52 PM Author: Russ Subject: Solder Ball After Reflow Process Oven settings are meaningless here. What does the board see? It is the paste we a
Electronics Forum | Wed Jun 11 16:30:33 EDT 2003 | T.Vick
You have received some great feedback so far. I would like to summarize and add a few points regarding maintenance. You should start (as recommended already) by verifying your component library data. Using the default values from the master library i
Electronics Forum | Sat Jun 09 00:53:34 EDT 2001 | ianchan
Hi Folks, My Production runs a uBGA-liken product, and uses Pallets to support the 0.8mm thick pcb, during the SMT + reflow oven process. Process/QA see occurs: 1) 0402 unsolder? 2) 0402 tombstone? 3) "uBGA" poor-visual joints (dry joints)? Took
Electronics Forum | Tue Mar 17 13:11:58 EST 1998 | ETS, LLC
ETS (Energy Technology Systems) is a manufacturer of Solder Reflow and Curing Ovens for the Electronics Industry. We offer a specially configured oven designed for processing of Pin in Paste processes as well as double sided mix technology boards. I
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
