Technical Library | 2016-06-06 11:33:17.0
Learn how to choose a cable & harness tester that remains relevant as product design changes in addition to providing fast, reliable, accurate results. See how it can improve productivity even beyond the production floor.
Technical Library | 2020-11-10 15:43:25.0
Flexible hybrid electronics (FHE) interface rigid electronic components with flexible sensors, circuits, and substrates. This paper reports the reliability improvement of a FHE Human Performance Monitor (HPM), designed to monitor electrocardiography (ECG) signals.
Technical Library | 2016-01-07 19:13:23.0
The purpose of this study is to investigate the effect of plasma surface modification to improve adhesion strength between polytetrafluoroethylene (PTFE) and electroless copper plating. PTFE is widely used in many industries because of its unique electrical, thermal, and mechanical characteristics. However, because of its low surface energy, it is difficult to acquire enough adhesion strength between PTFE and other substances without surface modification. Plasma is well known as one of the surface modification techniques that improve adhesion strength.
Technical Library | 1999-05-07 10:14:57.0
This paper describes a model developed to calculate number of redundant good die per wafer. A block redundancy scheme is used here, where the entire defective memory subarray is replaced by a redundant element. A formula is derived to calculate the amount of improvement expected after redundancy. This improvement is given in terms of the ratio of the overall good die per wafer to the original good die per wafer after considering some key factors.
Technical Library | 2009-05-28 18:15:46.0
Considerable effort is ongoing to improve the efficiency and to move towards high-volume manufacturing of photovoltaic cells. Much attention has been focused on developing in-line processes to replace the current batch processes. A critical process to improve the performance of solar wafers is the application of Dopants. The basic requirement for this process is an automated method for applying a very thin, uniform film of Dopant to the silicon wafer as part of an in-line manufacturing process.
Technical Library | 2014-04-10 18:04:04.0
This paper is meant to be a guide and a reference to new and old members alike who wish to know about, understand, and improve on the decisions made and processes implemented to build the current solar panels. The following paragraphs in the introduction will lay out background information on solar panels and cube satellites. This entire document was written with the idea that the reader will be able to follow the decisions made to construct the solar panels and then with this knowledge find areas of the project for improvement.
Technical Library | 2009-08-26 19:32:32.0
Automated optical inspection (AOI) and automated X-ray inspection (AXI) have been around for some time in various configurations and both have played a role in improving the quality of circuit boards. While some companies opt for one technology over the other, each form of inspection contributes its own unique benefit to the manufacturing process.
Technical Library | 2014-06-05 16:44:07.0
Stencil printing capability is becoming more important as the range of component sizes assembled on a single board increases. Coupled with increased component density, solder paste sticking to the aperture sidewalls and bottom of the stencil can cause insufficient solder paste deposits and solder bridging. Yield improvement requires increased focus on stencil technology, printer capability, solder paste functionality and understencil cleaning.(...) The purpose of this research is to study the wipe sequence, wipe frequency and wipe solvent(s) and how these factors interact to provide solder paste printing yield improvement.
Technical Library | 2017-10-26 01:18:49.0
Nano-coatings have been introduced by various manufacturers, with the promise of addressing some of the challenges relative to solder paste printing. Stated benefits include: Reduced underside cleaning, reduced bridging, improved solder paste release and improvements in yield. With several nano technologies already on the market and more likely to be introduced, how can the performance be quantified? How robust are these coatings? How can an assembler approach the ROI of these coatings? What hidden benefits or negative impacts should be considered? This paper will present a rigorous method for evaluating the performance and economic benefits of solder paste stencil nano-coatings.
Technical Library | 2018-10-24 18:04:12.0
Polymer Thick Film (PTF)-based printed electronics (aka Printed Electronics) has improved in durability over the last few decades and is now a proven alternative to copper circuitry in many applications once thought beyond the capability of PTF circuitry. This paper describes peak performance and areas for future improvement.State-of-the-art PTF circuitry performance includes the ability to withstand sharp crease tests, 85C/85%RH damp heat 5VDC bias aging (silver migration), auto seat durability cycling, SMT mandrel flexing, and others. The IPC/SGIA subcommittee for Standards Tests development has adopted several ASTM test methods for PTF circuitry and is actively developing needed improvements or additions. These standards are described herein. Advantages of PTF circuitry over copper include: varied conductive material compositions, lower cost and lower environmental impact. Necessary improvements include: robust integration of chip and power, higher conductivity, and fine line multi-layer patterning.
