Electronics Forum | Tue Jul 27 16:22:17 EDT 1999 | Earl Moon
| I'm working on a prototype board that requires a 600 pin BGA. This is a metal top BGA being placed on a 11" x 17" PCB about .62" thick. | | The part is 1.77" square with a 50 mil pitch and 30 mil bump diameter. The bumps are located on the
Electronics Forum | Wed Oct 03 23:59:44 EDT 2018 | gaintstar
Flason SMT problem solving: http://www.flason-smt.com/new/PRINCIPLE-OF-SURFACE-MOUNT-PROCESS-SMT-PROCESS.html http://www.flason-smt.com/new/Printed-Circuit-Board-PCB-Price-Estimator.html http://www.flason-smt.com/new/Printed-Circuit-Board-Solder-res
Electronics Forum | Mon Apr 25 12:19:21 EDT 2005 | siverts
Hi all, We produced a RoHS (lead-free) prototype order recently, and there was some components that we needed to replace on a couple of PCBA's. We found it very hard to do this even with the new solder iron. The components was just small RoHS SOIC's
Electronics Forum | Mon Apr 23 17:30:08 EDT 2001 | davef
Step 1: Print paste on the board, skip placement, reflow the board, check solderability. Step 2: Goto Step 1. White Tin Solderability: The most common reason for solderability issues with the white tin surface coating during multiple thermal excur
Electronics Forum | Mon Aug 07 18:20:40 EDT 2000 | Darby
James, I only use the clamshells for fine pitch if my other printers are non operational. Not reccommended but achievable in an emergency. In answer to your questions. We use two clam shell printers and two vertical lift printers. All are used for 8
Electronics Forum | Wed Mar 24 23:12:48 EDT 2021 | grahamcooper22
0.66 area aspect ratio...so for example...if the device is 0.5mm pitch QFP, the pcb pad may be 12 thou wide..make the aperture 9 to 10 thou wide...and reduce it's length by 10 % overall compared to the pcb pad.... Depending on device pitch, select ap
Electronics Forum | Thu Jul 29 11:14:46 EDT 1999 | Justin Medernach
| I'm working on a prototype board that requires a 600 pin BGA. This is a metal top BGA being placed on a 11" x 17" PCB about .62" thick. | | The part is 1.77" square with a 50 mil pitch and 30 mil bump diameter. The bumps are located on the
Electronics Forum | Tue Nov 07 09:26:37 EST 2000 | Peter Barton
Adam, The most common cause for this problem is a variation in the plating thickness of the through holes, particularly if they are Sn/Pb solder levelled PCB's. Most pressfit connectors require a fairly tight control on the diameter of the holes to
Electronics Forum | Tue Feb 03 16:42:50 EST 2009 | cuperpeter
Hello All, > > I have a problem with nonwetting Au > finish after second cycle of reflow soldering > doublesided boards. Solder nonwetted pcb pads (is > wicked to component terminations) Either these > pads or some of non component pads became
Electronics Forum | Mon Oct 02 11:20:44 EDT 2000 | aaronho
It's not really you need a book. You can ask your stencil supplier for what to... The supplier should be an expert in stencil making. Basically pitches and apertures should be made to the spec in CAD data of PCB. You can ask to make to 90% size of pa
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
winsouce.jpg)
