Electronics Forum | Mon Feb 04 20:27:25 EST 2002 | davef
1,000 G ohm ||100 M ohm Dielectric Constant ||9.5 ||4.9 Loss Factor ||5 - 20 ||200 * E indicates exponent Continuing: * Spacing between same plane traces effect the electical parameters between the traces. * Dielectric materials used between diff
Electronics Forum | Tue Feb 19 14:00:55 EST 2002 | global
We have had some discussions about what causes parts to lift out of the holes when going over the wave on our flow solder machine. The machine being used is a Treiber (700 series). There are two bottom pre-heaters and one top pre-heater. We try to pr
Electronics Forum | Thu Apr 04 16:38:51 EST 2002 | davef
Equipment companies like to talk about �accuracy� and �repeatability�. These measures provide limited information. Flaws of the measure aside, some printer companies have begun to report Cp. * DEK ELA: Cp = 1.33 @ �0.025mm * DEK 265: Cp = 1.6 @ �0.0
Electronics Forum | Fri Apr 05 13:42:05 EST 2002 | dougt
We have been using a silicone encapsulated, high flex, flat cable for a short time now and have not been succusfull in terminating it to connectors with shell housings designed for round cable. Our solution thus far has been to leave the housing off
Electronics Forum | Thu Apr 11 19:06:59 EDT 2002 | tmarc
We are using 1mm pitch BGAs with a great quantity of via(s) under the component. Very shortly we will be placing CSPs with .65mm pitch. Our via(s) are solder masked, however we generally have a percentage of them that the masking is thin enough that
Electronics Forum | Tue May 14 13:18:33 EDT 2002 | Scott B
I think what David was getting at was, as an example. Take a cubic inch of gold. Surface area = 6 sq/in. Volume = 1 cu/in. Water displacement = X. Mass = Y Roll that cube of gold out to a micron thick. Surface area = football pitch. Volume = 1 cu/i
Electronics Forum | Thu Jun 06 07:28:30 EDT 2002 | cyber_wolf
It has been my experience that the only thing(s) that will ever cause this is: 1. Operators with paste on their hands. 2. Paste on the screen printer tooling. 3. Paste on the bottom of the stencil. Even very very small amounts of paste on the gold fi
Electronics Forum | Wed Jun 19 14:44:11 EDT 2002 | kenbliss
It sounds like your inspector improved quality and pre-staging your feeders dramaticaly increased uptime on your machine, thats great to hear. One cautiionary note, be careful not to flood your production area with parts off of your SMT line. With
Electronics Forum | Mon Jul 01 20:42:54 EDT 2002 | davef
Comments [questions] are: * It�s strange that an uggie ol� SOIC, 50 pitch, BIG honkin� solder pad, kinda thang is failing. Sumpin aint kosher, yano? * Where is the failure occurring [ie, lead to pad, pad to board, etc]? Talk about the breadth and di
Electronics Forum | Thu Jul 18 21:04:06 EDT 2002 | davef
So, why can't you clean misprints on Entek boards? Entek: Cheap, flat, OK shelf life, not without process and fabrication issues. Your Entek organic solderability protection is probably Entek Plus [CU106A] made by Ethone OMI. Consider getting a co
Manufacturer of PCB depaneling and PCB soldering machines since 2005, products include CE approval V-groove PCB depanelizer, PCB router, PCB punching machine, laser depaneling, hot bar soldering machines and soldering robots.
Liwu Industrial Park, Yuanzhou Town, Boluo
Huizhou, 30 China
Phone: +86-138-29839112
