11169 parts results

Electronics Forum: parts (Page 515 of 1117)

SMT Equipment

Electronics Forum | Mon Jul 29 08:28:05 EDT 2002 | pjc

Start killing DEK now, on the ELA. All DEK 248 semi-auto printers have been built in China for quite some time (years). Its shipped to the UK from China. All DEK ELA models are now built in China, since 01 some time. Thats the fact Jack. All MPM mod

Indium No-clean and Inert Reflow oven (N2)

Electronics Forum | Thu Aug 01 12:55:41 EDT 2002 | johnw

we run the paste in both air and n2 depending on customer requirements again it run's fairly well in both. Some people say it's better sme say it doesn't make a bit of difference, I'm somewhere in between at the moment. I definately think there's imp

Baked Components

Electronics Forum | Thu Aug 15 22:35:54 EDT 2002 | Brandon

I've done some experiments on baking parts as we got pop corning QFP's on our production line. This QFP has moisture level of 5 and I baked them @ 125'C for minimum of 12 hrs. So far results were great but I have a question: Forum says that I cannot

Poor Fuji recognition of PhyComp 0603 (1608) cap

Electronics Forum | Tue Sep 10 23:37:22 EDT 2002 | Steve E

Dear Sir I can assure you that I have personal experience with the part in question.This part will run with the recommend vision types ( 11 & 12 ). I noticed You neglected to state how old the machine was, and the amount of hours. The CP-6 series hav

Nozzle size

Electronics Forum | Thu Sep 12 18:37:09 EDT 2002 | tiusa

Hi Tony, as you might guess, a Nozzle Mfg. has stepped into this conversation. Having worked with many small, mid-size, and Fortune 500 companies for almost 15 years we have seen many "parts" pick up challenges. We were the first to offer "Complia

pc board defects

Electronics Forum | Sun Sep 15 15:08:00 EDT 2002 | jersbo

My 2 cents... Screen printing may very well have a leg up on deciding SMT defects... however if you pay attention to your stencil (aperture size ratio etc..) and inspect your prints... I believe its a much lesser number... (paste MFG also plays a ro

MPM AP25 Parts

Electronics Forum | Tue Sep 24 07:32:58 EDT 2002 | cyber_wolf

Pete: It is a Panasonic Camera. MPM tells me that they no longer sell parts for that vision system, and in order to fix this problem I have to do a vision up-grade. The upgrade is over 20K if I remember correctly. That is not going to happen. I hav

BGA rework stencils ( down to 0.65mm pitch)

Electronics Forum | Mon Oct 14 03:14:08 EDT 2002 | msimkin

Hi, Has anyone had expereince in the design or use of mini rework srtencils for uBGA applications? What was the deisgn guide lines used. I am looking to rework 0.7 & 0.65 mm uBGA parts with standard hot air, without split prism placement guides. It i

PCBA baking prior to rework

Electronics Forum | Tue Oct 15 10:12:44 EDT 2002 | davef

1) Do people always bake, sometimes or never? Does this depend on whether MS sensitive components are near the rework site? If a BGA is to be removed and reballed, baking is a no-brainer. Sometimes, based on the proximity of the MS components. >2)

Re-soldering QFP with thermal pads

Electronics Forum | Thu Oct 31 09:34:38 EST 2002 | russ

We do this all of the time, This is what we do but I would be interested in other methods. 1. Remove component with BGA type rework station 2. Wick off lead pads only, verify/create even solder surface on the thermal pad on the board 3. Apply no-cle

515