Technical Library | 2020-11-29 22:06:45.0
Plastic laminates are increasingly used as interposers within chip packaging applications. As a component within the package, the laminate is subjected to package moisture sensitivity testing. The moisture requirements of chip packaging laminates are related to ambient moisture absorption and thermal cycling. Printed wiring board (PWB) laminates, however, are gauged on properties relating to wet processes such as resist developing, copper etching, and pumice scrubbing. Consequently, printed wiring board moisture absorption test methods differ from chip packaging test conditions.
Technical Library | 2020-12-24 02:34:23.0
The advance in technology and its relentless development is delivering yet another surface mount assembly challenge. To meet the market demand for products with higher functionality whilst reducing the overall product size, the next generation of chip package is being readied upon the surface mount community. The Metric 0201 will have dimensions in the order of 0.25mm x 0.125mm, as a result the entire assembly process will be questioned as to its ability to deliver high volume/quality product.
Technical Library | 2020-01-02 12:16:02.0
A customer contacted the Helpline with the concern that parts being used in their assembly may possibly be counterfeit components. The counterfeiting of electronics components is a world-wide problem, and the threat today is even more evident than ever before. Any company, large or small, that manufactures assemblies using electronics components is equally susceptible to using counterfeit devices in their assemblies. In most cases, counterfeit components aren't discovered until after the component has already been placed on a printed circuit board (PCB), usually during first article electrical test. At this point, the only recourse is to debug the circuit to determine the faulty component and rework each PCB already in production to replace the faulty component. As one might easily surmise, this is a rather costly process; world-wide, counterfeit components account for over $15B loss in sales annually!
Technical Library | 2020-01-09 00:00:30.0
PCBs have a wide range of applications in electronics where they are used for electric signal transfer. For a multilayer build-up, thin copper foils are alternated with epoxy-based prepregs and laminated to each other. Adhesion between copper and epoxy composites is achieved by technologies based on mechanical interlocking or chemical bonding, however for future development, the understanding of failure mechanisms between these materials is of high importance. In literature, various interfacial failures are reported which lead to adhesion loss between copper and epoxy resins. This review aims to give an overview on common coupling technologies and possible failure mechanisms. The information reviewed can in turn lead to the development of new strategies, enhancing the adhesion strength of copper/epoxy joints and, therefore, establishing a basis for future PCB manufacturing.
Technical Library | 2020-02-19 23:12:55.0
Silver nanowires (Ag NWs) possess excellent optoelectronic properties, which have led to many technology-focused applications of transparent and flexible electronics. Many of these applications require patterning of Ag NWs into desired shapes, for which mask-based and printing-based techniques have been developed and widely used. However, there are still several limitations associated to these techniques. These limitations, such as complicated patterning procedures, limited patterning area, and compromised optical transparency, hamper the efficient fabrication of high-performance Ag NW patterns. Here, we propose a coat-and-print approach for effectively patterning Ag NWs.
Integrated Microwave Packaging Antennas and Circuits Technology (IMPACT) Lab
Technical Library | 2020-03-19 00:23:15.0
In this study, the question was how to perform statistically reliable robust- ness tests for the non-contact drop-on-demand printing of functional fluids, such as solder paste and conductive adhesives. The goal of this study was to develop a general method for hypothesis testing when robustness tests are performed. The main problem was to determine if there was a statistical difference between two means or proportions of jet printing devices. In this study, an example of jetting quality variation was used when comparing two jet printing ejector types that differ slightly in design. We wanted to understand if the difference in ejector design can impact jetting quality by performing robustness tests. and thus answer the question, "Can jetting differences be seen between ejector design 1 and design 2"?
Technical Library | 2020-04-01 05:52:59.0
Recently, our engineer Peter went to Thailand to provide after-sales support for our customer. In these days, we had installed a SC-900 selective coating line . Moreover, Peter gave patience and meticulous training to their staff, make sure they master the machine usage .Customer and agent are satisfied with our support and give their affirmation to us. SC-900 is a high Performance 4 axis Selective Coating Machine ,which is equipped with high precision servo control system , various valves , CCD system ,material tank weight detecting system etc, which can provide a high efficiency conformal coating process .The maximum coating size can reach 400mm*450mm with SC-900. So far, we've installed several dozen conformal coating line all over the world. It have excellent stability and performance. Check below link to get more info!
Technical Library | 2020-04-01 23:32:29.0
Low temperature solder alloys are preferred for the assembly of temperature-sensitive components and substrates. The alloys in this category are required to reflow between 170 and 200oC soldering temperatures. Lower soldering temperatures result in lower thermal stresses and defects, such as warping during assembly, and permit use of lower cost substrates. Sn-Bi alloys have lower melting temperatures, but some of its performance drawbacks can be seen as deterrent for its use in electronics devices.Here we show that non-eutectic Sn-Bi alloys can be used to improve these properties and further align them with the electronics industry specific needs. The physical properties and drop shock performance of various alloys are evaluated, and their results are analysed in terms of the alloy composition, including Bi content and alloying additions.
Technical Library | 2020-04-08 22:57:04.0
Flexible hybrid electronics (FHE), designed in wearable and implantable configurations, have enormous applications in advanced healthcare, rapid disease diagnostics, and persistent human-machine interfaces. Soft, contoured geometries and time-dynamic deformation of the targeted tissues require high flexibility and stretchability of the integrated bioelectronics. Recent progress in developing and engineering soft materials has provided a unique opportunity to design various types of mechanically compliant and deformable systems. Here, we summarize the required properties of soft materials and their characteristics for configuring sensing and substrate components in wearable and implantable devices and systems. Details of functionality and sensitivity of the recently developed FHE are discussed with the application areas in medicine, healthcare, and machine interactions. This review concludes with a discussion on limitations of current materials, key requirements for next generation materials, and new application areas.
Technical Library | 2020-06-19 19:08:14.0
The designs of electronic devices and systems are being continuously improved by becoming smaller in size and faster in communication speed. The potential risk associated with these specific design improvements will be an increase in power density and, consequently, a greater risk of thermal problems and failures. At the same time, the prevailing use of circuit boards integrated with power devices such as motor controllers and drivers, light-emitting diode (LED) lighting modules, power supplies, and amplifiers, and regulators for TV, etc., drive to the use of a proper thermal management system while designing these kinds of printed circuit board (PCB).
