Electronics Forum: csm84vz (Page 6 of 8)

Puzzling CSM84VZ errors, #118 and #120

Electronics Forum | Thu Nov 10 00:38:54 EST 2011 | tpappano

Hi Jeff, no problem, I'll just pop them out and make copies. I'm betting the upgrade will take care of these silly problems. The machine with the "newer" firmware just goes and goes without any issues other than replacing that R-axis servo a while

CSM 84VZ Head Replacement

Electronics Forum | Mon Apr 08 16:41:07 EDT 2013 | rgduval

I need to replace the number 1 head on my CSM84. The nozzle is stuck in the tube, and I haven't been able to get it out. I have, however, done a number on the nozzle while trying :) I have a new head to put in there, but, am being stymied by the r

CSM 84VZ Head Replacement

Electronics Forum | Tue Apr 23 09:49:18 EDT 2013 | rgduval

Thanks, Jeff. I ended up bringing someone in to help me with it. And, that's pretty much what we did. What a pain! Who ever designed these heads never expected them to fail, apparently! The actual head change out only took about a half hour (inc

Phillips CSM84VZ Questions

Electronics Forum | Wed Jan 19 17:04:57 EST 2011 | gosswald

I have been looking at Quad IVC machines as they come close to my budget and needs. I recently looked at a Phillips CSM84VZ in a warehouse that has been taken out of operation locally. The machine has probably been setting for about two years. It h

Can CSM84V and CSM84VZ do 0402 ???

Electronics Forum | Mon Apr 17 22:54:51 EDT 2006 | Darby

Short answer is - not really. According to the manual in Chapter 1-5 Supply devices (Feeders) overview "There are also available an 8mm tape feeder which handles 1005(0402) square chips". I have never seen one. The problem is that even an H nozzle is

Re: Opinions on Yamaha YM84V II

Electronics Forum | Mon Nov 30 16:19:44 EST 1998 | Brian McCarthy

| We are considering a used Yamaha YM84V II to add to our existing compliment of stand-alone machines. The brochure states that it can place 0603 devices as standard. Is this true? Do you know of any quirks with these machines? Any comments would be

Fine pitch & PCB finish

Electronics Forum | Mon Feb 21 18:13:23 EST 2005 | gpaelmo

As davef states above, you would like to have flat surfaces below 25 mil. We are a contract manufacturer also and we've done thousands of 15 mil QFP's with HASL finish with no problems. Your success will depend on quality of PCB supplier providing th

Researching placement machines - where do I start?!

Electronics Forum | Sat Oct 31 09:45:48 EDT 2009 | meritajs

Hello Jeffrey J I could share our experience in using used P& P machine type Philips (Yamaha) and Juki (Zevatech) We had three machines Philips (Yamaha) vintage about1990g, which work till now. They have same type of feeders, which is simple to find

Need Help Operating CSM84VZ

Electronics Forum | Wed Jan 05 21:25:15 EST 2011 | jeffr

Error 215 is due to corrupt memory. I suggest that you start by replacing the Lithium battery on the Mother Board. Next, remove the cable from the Floppy unit and turn on the machine with it disconnected. Goto the SYSTEM menu and find the menu "DATA

Need Help Operating CSM84VZ

Electronics Forum | Fri Jan 07 01:36:46 EST 2011 | jeffr

David, Assuming your machine has a WHITE controler, not a SILVER controler, there is a floppy drive inside the front panel of the controler. (Remove the top cover to reach the 50pin cable.) If Tom offers you a disk to try in the machine, go ahead. T


csm84vz searches for Companies, Equipment, Machines, Suppliers & Information

Global manufacturing solutions provider

World's Best Reflow Oven Customizable for Unique Applications
Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.