Full Site - : quad iv c srx (Page 7 of 8)

Quad IV-c feeder error

Electronics Forum | Fri Feb 01 07:21:32 EST 2019 | dfl

One of my 8mm feeders is blinking the red led after the pick-up. With both buttons the motor works as expected (forward/backward), but after the nozzle pick-up the motor moves forward and then the red led blinks. pressing the buttons the green led l

Quad IV-c feeder error

Electronics Forum | Sat Feb 02 09:53:49 EST 2019 | slthomas

Commponent pitch programming is performed via the buttons on the feeder. I don't remember enough to walk you through it but there are people here that do - I'm sure you'll get some help shortly. If not, go to http://www.precision-repairs and use th

Quad IV-c feeder error

Electronics Forum | Sun Feb 03 08:46:34 EST 2019 | dfl

SOLVED The LED/phototransistor was a little of the center on the "index wheel" (don't know a better name, its the gear that pulls the component strip). The wheel works with a LED from one side and a phototransistor from the other, through a hole on

Quad IV-c feeder error

Electronics Forum | Sun Feb 03 09:36:29 EST 2019 | bobpan

Good job.... Sorry i didnt see this post...some of us were busy snow tubing over the weekend...haha. Many times over the years....the rubber belt inside the feeder will deposit material inside. Sometimes it ends up on the sensors and blocks the ligh

How Quad Align works? (Quad IV-c machine)

Electronics Forum | Fri Aug 02 12:03:16 EDT 2019 | dfl

UPDATE: I was reading around about similar problems. My function #30 always return nozzle height 1. I tried to clean up the glasses and the internal laser lenses, no go, still at height 1. Even after removing both glasses, still at height 1. I saw s

How Quad Align works? (Quad IV-c machine)

Electronics Forum | Sun Aug 04 08:47:12 EDT 2019 | dfl

Hey bob, I had no luck. Even removing both glasses, cleaning that curved lenses with a cotton swab and isopropanol and blowing compressed air, the height still on 1. I will try on the next weekend again, to be sure, but my first guess is the QA un

Quad IV C Recommendations

Electronics Forum | Tue Jan 11 13:28:14 EST 2011 | jmw

0603 and up should be no problem on the machine. If you are doing under 25 mil pitch the machine needs an upward camera to repeatably place the parts. You will always lose the first 10 or so parts with cut tape but that should be about it. Repair par

Quad IV-c with Y-axis problem

Electronics Forum | Wed Jan 30 15:08:10 EST 2019 | dfl

MM, exchange the cards doesn't make any difference. The problem happens when the machine is moving from left to right. Right to left works all the time. bobpan, thanks, I completely missed this one. The default was 0 and now is set to 1. The build c

How Quad Align works? (Quad IV-c machine)

Electronics Forum | Fri Aug 02 08:12:55 EDT 2019 | dfl

Hey guys, I'm using my Quad IV-c for a while now and I already manage to run some batches, but I never used the "Quad Align" feature before, since almost all my boards are 1206 parts, that doesn´t need a ton of precision to align. Anyway,

Quad IV C Recommendations

Electronics Forum | Mon Jan 10 17:12:53 EST 2011 | gosswald

I have been researching older lower cost used Pick and Place machines and so far I am leaning towards the Quad IV C. There seems to be a fair amount of these units around and I have heard some pretty good things about them on some of the past posts.


quad iv c srx searches for Companies, Equipment, Machines, Suppliers & Information

2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
See Your 2024 IPC Certification Training Schedule for Eptac

World's Best Reflow Oven Customizable for Unique Applications
Online Equipment Auction Jabil Monterrey MX Aug 19, 2024

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
PCB Handling with CE

Component Placement 101 Training Course