Electronics Forum: hydra (Page 8 of 21)

Mydata TP11

Electronics Forum | Wed Sep 21 12:12:24 EDT 2005 | vikkaraja

HI there, I have a problem with my TP11 HYDRA HEAD. It is not picking up parts from the magazine. I have been working with Mydata on this issue, but I have not had much success so far. So far I done the followings:ran vaccum test, tube height, and H

Mydata MY12 Hydra Theta error

Electronics Forum | Mon Nov 21 21:46:49 EST 2011 | supse

Thanks Phil But the belt and spring has been changed recently. Unfortunatly we couldn't wait any longer for a solution, so we had to go for a change of the hydra-unit. This seems to have solved the matter, but I had hoped for a less expensive solutio

Mydata Hydra tool reference mark error

Electronics Forum | Sat May 04 14:36:53 EDT 2013 | dontfeedphils

It's been a while since I've used a MyData but I believe what happens is on the bottom of the hydra black metal piece is a mark that the vision system uses to locate the tools as they pass over to center the parts. Something may have happened to this

Need help on buying part for IEMME ITALIA Hydra 1662 Wash Machine.

Electronics Forum | Mon Sep 24 13:27:05 EDT 2018 | tey422

I need help right away on finding the replacement parts for the IEMME ITALIA Hydra 1662 wash machine. I been searching for web for it, and no luck of finding it. I would like a part number list from manual if available so I can search and purchase

MYDATA HYDRA Z/156 error on Hardware Intialization.

Electronics Forum | Fri Mar 06 14:33:53 EST 2020 | bk

Another thing you can check is where the bar comes down off of the hydra z motor there is a little bearing you can see from the front make sure that bearing is turning even oil it up a little. You can also adjust the tension by loosening the tiny set

mydata disable a bad Hydra setup to continue running

Electronics Forum | Tue Dec 21 17:15:49 EST 2021 | vtdivtecs

yeap I was able to figure it out and avoid my head being on a stick anywhere. if you log out of tpsys and into hw config you can turn off the hydra head there, then unplug the hardware and the machine will run. if you just disable it inside tpsys t

Force sensor error on MyData My12

Electronics Forum | Thu Dec 28 20:46:49 EST 2023 | padawanlinuxero

I was use to work with the machine but it has being several years since I had one in my hands, but i got the same error message, I kinda remember there are some sensors in the top part of the hydra try to see if theres dirt or something not letting t

MyData 12 errorF-TLMN-18

Electronics Forum | Fri Jan 05 16:16:51 EST 2024 | mistrthou

Based on the my15 we used to have and our current My100's I'd say it lost the position of the tool bank. Is it Hydra or Midas tooling? Uninstalling and reinstalling the hydra tool bank is fairly easy. If it's Midas tools, does it fetch other tools

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Tue Apr 02 18:25:00 EDT 2024 | kingkelvin

Yes very good - thank you, I'm getting the specific hydra tool offset jig from PFI Florida for $100 - and MyData has already quoted me all the other parts such as in that box there - so I'll get some of these in and continue my work. Thanks all!

Mydata Users

Electronics Forum | Wed Apr 26 14:06:46 EDT 2006 | mdm4ua

Hi JEM, We just made the very same upgrade you are looking to make on three machines. We purchased a new MY12 and upgraded our other three (My9 W/hydra, My9 No Hydra, and TP9-2U) from 2.2.4C to 2.4.4c. There are several changes and most of the


hydra searches for Companies, Equipment, Machines, Suppliers & Information

SMT spare parts - Qinyi Electronics

Component Placement 101 Training Course
SMT feeders

Stencil Printing 101 Training Course
Circuit Board, PCB Assembly & electronics manufacturing service provider

Best Reflow Oven
Win Source Online Electronic parts

World's Best Reflow Oven Customizable for Unique Applications