Electronics Forum | Mon Aug 05 03:03:50 EDT 2002 | jkhiew
Hi all, I had some old stock of CEM1 pcb: a. How long & under what temp. condition shall I bake it to eliminate the trapped moisture ? b. Is the baking time & temp. different for 3 yrs old stock, 2yrs old stock & 6 month old stock ? c. For CEM1 pcb,
Electronics Forum | Wed Jan 30 05:36:04 EST 2002 | vincent_f
Hello everybody, I would like to use PCB which have expired. I have already planned to bake them in order to avoid pop corn effect but I wonder about some few items : 1) How can I identify the optimal baking parameters ? 2) Even after baking, is the
Electronics Forum | Tue Jul 06 07:49:08 EDT 2004 | davef
Q1)What is the MSD level for PCB? A1) There is none Q2)I have some PCB's with HIC (humidity indicator card ) has turn to pink at 50%. Should I bake the PCB prior to assembly process.This fab is a complex board with various kind advance package assem
Electronics Forum | Mon Mar 19 13:44:13 EDT 2012 | vinod
If PCB supplier has stored PCB in complete IPC specified storage condition and let say they kept for 2 Years. Are these PCB still good for use? I understand about shelf life and baking procedure but I am not sure how long PCB are good for use if they
Electronics Forum | Fri Jun 01 23:57:21 EDT 2012 | bwjm
HI Guys, i am facing similar issues with this BT resin material too. PCB specs are 4 layers, Nelco400013, same Tg and Td. My PCB delam after reflow. The PCB has both side mounted with SMDs. Initial mounting on the btm side after reflow, no delam. B
Electronics Forum | Fri Jan 18 04:45:32 EST 2002 | wbu
Ianchan, baking as being part of pre-heating is obviously sensless cause the PCB will not maintain any of that heat till soldering. Common reason for prebaking PCB�s is getting the moisture out to prevent outgassing, warpage and maybe other defects.
Electronics Forum | Tue Jul 20 15:02:49 EDT 2010 | vetteboy86
I've seen this warp issue across several different PCB's we assemble. One of the biggest head ache's is getting the boards to transfer between machines, converyors, and inside our pick and place. Due to the warpage, transport between conveyors is dif
Electronics Forum | Fri Feb 25 10:23:46 EST 2000 | K3 Equipment
Greg, If you are having a problem, i would first check board manufacturers process. Also are they shipping boards to you in seal packages (a must if you are in a humid part of the country.) Most of the time with a few simple process controls moistur
Electronics Forum | Mon Feb 28 17:16:38 EST 2000 | Stu Leech
We just got a lesson on the effectiveness of heat sealed metalized vapor barrier bags. A customer sent us two bags of 100% saturated PBG components by air freight. This was for a demoisturizing test. When we found the devices 80% dry when they arrive
Electronics Forum | Fri Feb 25 10:23:46 EST 2000 | K3 Equipment
Greg, If you are having a problem, i would first check board manufacturers process. Also are they shipping boards to you in seal packages (a must if you are in a humid part of the country.) Most of the time with a few simple process controls moistur
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830