Industry Directory | Distributor
Northern Connectors are a specialist distributor of Electronic Connectors and Components that provide simple solutions.
Industry Directory | Equipment Dealer / Broker / Auctions
RMC Inc. is an independently owned company, established in 1997, owned and managed by ex IBM employees with more than 25 years experience each in product, manufacturing, quality and remanufacturing
Mechatronika MR10 is a fully programmable far infra red oven, suitable for reflow soldering as well as glue heat drying. Soldering sections are controlled by a microprocessor, that also enables the storage of up to sixteen parametrized temperature
New Equipment | Test Equipment
Aeroflex IFR 2399B A spectrum analyzer with outstanding performance and a user friendly visual interface simplifying many complex measurements. 9 kHz to 3.0 GHz fully synthesized frequency range Lightweight, portable and rugged construct
Electronics Forum | Sat May 29 14:03:18 EDT 2010 | padawanlinuxero
Hello guys! I have a problem I had to change the MI Board on a MYDATA TP9-4 machine because it was firing 3 or more feeders at the same time, after the change it run great but then for some reason after a while it start to show an error message that
Electronics Forum | Wed Jun 09 12:28:29 EDT 2004 | abarbe
Hi I'm looking for a user manual(copy) for camalot 1414. Software version 9.4(made in 1992). We will pay for the copy. Thank you
Used SMT Equipment | SMT Equipment
1999 Mydata TP9-4 SMT Pick & Place Machine Dimensions: 104" L x 52" W x 60" H Cycle Count - 04317950 Serial: 4235 Item Location: Tampa, FL USA
Used SMT Equipment | Pick and Place/Feeders
1.) GSM2 with PTF 2 flexheads 4 mil ULC Left to right Front fixed No feeders 2.)GSM1 1 flexhead EPC9 4 mil ULC Left to right front fixed No feeders Elexin Engineering
Industry News | 2022-06-24 10:31:43.0
North American EMS Industry Up 9.4 Percent in May
Parts & Supplies | Assembly Accessories
carbon brush 9498 396 01388 CARBON BRUSH ..N606DP64-042 CARBON BRUSH ..N65021 Carbon Brush ..N65000 Carbon Brush For HIOS CL-3000] Carbon Brush Carbon Brush X Motor (LAS) ..5322 479 30166
Parts & Supplies | Chipshooters / Chip Mounters
Típus/Type Méret/Size NF08N 8*2 NF08N 4* CF05HP 2* CF081E 2* NF24FS 10*12*9*8 NF12FS 4*9 NF24SE-00067 6* NF8L1E 4* NF12NS 12*4*8 NF24NS 8*10*9*4 NF24SE 12*16*20A*24 NF24 10*3*4*8 FF
02190110-01 *SUBSTITUTE=00142911 M-MAG-11MM / B=7,5/ 02190113-01 *SUBSTITUTE=00302256 M-MAG-20MM / 32 PIN 02190115-01 *SUBSTITUTE=00302258 M-MAG-18MM / TO 220 02190116-01 *SUBSTITUTE=00302270 M-MAG-37,5MM / PLCC 02190121-01 *Substitute=00302230 M
00357288-01 FUSE 5x20 10A WITH DELAY 00357289-01 FUSE 5x20 / T 1,6A / Glas 00357328-01 BACKPLANE KSP-SYSS23 00357744S01 Adapter e156 00357795S01 PNEUMATIC-SERVICING-UNIT 00357871-01 SOCKET PROTECTION TEDDY 6310 WHITE 00357969-02 Velcro Tape for
Events Calendar | Wed Sep 11 00:00:00 EDT 2024 - Wed Sep 11 00:00:00 EDT 2024 | Oshkosh, Wisconsin USA
Wisconsin Chapter In-Person Event: PCB Workshop and PCB Plant Tour
| https://www.eptac.com/faqs/ask-helena-leo/ask/ipc-a-610-acceptable-requirements-for-nicks-and-chip-outs
: In IPC-A-610 section 9.4 on page 9-8 component damage there seems to be a lack of class three acceptable requirements for nicks or chip-outs in ceramic bodied components that are not in the termination area
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_pads-productivity-kit_topic33.xml
! I already know these modeless commands. I was just curious of the "bells and whistles" and thought/hoped this tool could have been updated for the version 9.4
