Industry Directory | Consultant / Service Provider / Manufacturer
From Proto to Production to Service we are fully equipped to build through the entire spectrum of heritage through-hole, to fine pitch SMT, to complex Package on Package designs.
New Equipment | Rework & Repair Equipment
Orange Sticks with double beveled ends, 7" x 5/32" (SH-83) The Beau Tech orange sticks are made of high quality non-resin wood which will not contaminate solder and component leads. Natural wood is among the best material that does not gen
Formed parts are used for electrical insulation, such as snap-in-place housings, protection of high voltage parts, or covering bus bars. Plastics Forming Methods: Heated line bending Press brake cold forming Perforating for bend in plac
Electronics Forum | Thu Dec 12 12:54:25 EST 2013 | jaimebc
For selective soldered components, or even hand soldered, with vertical bend components, the body of the component, in this case a resistor, is making contact with the surface of the PCB, making it impossibe to visually see the solder fillet. Or to d
Electronics Forum | Fri Dec 13 10:06:05 EST 2013 | davef
For vertical mounted, axial leaded components; the standoff from the land to the component body should be 0.4mm[0.016in] to 1.5mm[0.059in]. Right?
Used SMT Equipment | Preheaters
PCB flatness Inspection Machine PCB, warpage bending defect detection Inspection Range : 0 ~2000um
Used SMT Equipment | SPI / Solder Paste Inspection
SPI PARMI SPI HS60L PARMI solder paste inspection machine SPI HS60 product introduction: 1. The SPI HS60 Series series is PARMI's best-selling model. It has been installed in excellent SMT production sites around the world. Its performance st
Industry News | 2011-12-14 15:35:33.0
Manufacturing processes, handling and printed circuit assembly (PCA) test can put a lot of mechanical stresses on packages, causing failures. As grid array packages get larger, identifying how to set safe levels for these steps becomes more difficult. A new quantitative test methodology within IPC/JEDEC-9707, Spherical Bend Test Method for Characterization of Board Level Interconnects, lets users determine how much strain packages can take before reliability degradation.
Industry News | 2012-03-28 08:47:23.0
he industry standard that establishes the specific requirements for the design of flexible and rigid –flexible printed boards, IPC-2223, Sectional Design Standard for Flexible Printed Boards, has been recently updated to its C revision.
Parts & Supplies | Assembly Accessories
BEARING ..603-04-071 BEARING PIN ..603-04-062 BEARING PIN ..603-00-141 BENDING CUTTER ..556-N-1032 BENDING CUTTER ..556-N-1042 BENDING CUTTER (A) ..556-T-0150 BENDING CUTTER (A) ..556-T-0042 BENDING CUTTER 1A ..556N10
Parts & Supplies | SMT Equipment
N210028285AA BENDING DIE for AV131
Technical Library | 2021-02-25 14:19:00.0
This study proposes a new design of lightweight and cost-e#14;cient composite materials for the aeronautic industry utilizing recycled fresh scrap rubber, epoxy resin, and graphene nanoplatelets (GnPs). After manufacturing the composites, their bending strength and fracture characteristics were investigated by three-point bending (3PB) tests. Halpin–Tsai homogenization adapted to composites containing GnPs was used to estimate the moduli of the composites, and satisfactory agreement with the 3PB test results was observed.
Technical Library | 2009-05-21 13:41:05.0
Failure due to board flex cracks persists as the dominant failure mode in multi-layer ceramic capacitors (MLCC). (...) This paper is intended to show the impact of temperature cycling, high-temperature life tests, and multiple bend exposures to the MLCC with this flexible termination.
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
https://www.ascen.ltd/Products/Component_lead_forming_machine/ Motorized version ASCEN taped component axial lead forming machine AS-809F axial lead former, use for cut and bend axial components braid resistor,capacitor, inductor, diode and other ele
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Career Center | Allentown, New Jersey USA | Production
Responsibilities: Set-up and operate surface mount equipment Ability to perform SMT repair Two years SMT machine operation experience required Ensure that assembled product meets ISO-9001 standards Responsible for keeping the work area clean and saf
Career Center | Auburn, Massachusetts USA | Production
Manufacturing company has an immediate opening for an experienced CNC Press Brake Operator. They offer modern machinery. Job requirements and qualifications; * 5+ years experience setting up and operating CNC Hydraulic press brakes. * Ability to
Career Center | Torrington, Connecticut | Engineering,Management,Production,Quality Control,Sales/Marketing,Technical Support
MECHANICAL AND ELECTRONIC CAD TECHNOLOGY-CERTIFICATION • TECHNICAL DRAFTING: Equipment Use, Orthographic Projection, Dimensioning, Auxiliary Views, Fasteners, Manufacturing Processes and Fits and Tolerances • POWER TRANSMISSION/ANSI 14.5 1994: Bearin
Career Center | Brookfield, ALL USA | Management,Production
Training and Qualifications Mil standards 464 Mil Standards 2000 ESD Training Cellular Manufacturing TQM Totally Quality Manufacturing ISO 9000 and 9001 IPC Standards, IPCA-610 IPC-J-STD-001E OSHA training LEAN Manufacturing, JIT (Just In T
The Application of Spherical Bend Testing to Predict Safe Working Manufacturing Process Strains SMTnet Express January 9, 2013, Subscribers: 26086, Members: Companies: 9075, Users: 34138 The Application of Spherical Bend Testing to Predict Safe
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/RSS_question-about-oscillator-lbend-definition_topic957.xml
PCB Libraries Forum : Question about Oscillator, L-Bend definition PCB Libraries Forum : Question about Oscillator, L-Bend definition This is an XML content feed of
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/qy91222-bnc-male-bend-to-bnc-male-2-5m-228979?page=16&order=list_price+asc
BNC Male bend to BNC Male 2.5M | Qinyi Electronics Co.,Ltd × Home about Us ABOUT US FAQ SMT spare parts SMT surplus equipment SMT peripheral equipments News Contact US 0 0 Sign in contact us Products BNC Male bend to BNC Male
