New Equipment | Wave Soldering
ZH-220 PCB welding desk small mini wave soldering machine 1. The circular arc appearance, streamline design. 2. Into the board straight association-like into the board device, stainless steel chain transmission, ensure smooth PCB into the machines.
Electronics Forum | Tue Sep 14 06:00:27 EDT 2004 | sc
dear, appreciate the sharing of experience on detection tools of cold soldering defect on PCBA. thanks SC
Electronics Forum | Tue Sep 14 06:00:31 EDT 2004 | sc
dear, appreciate the sharing of experience on detection tools of cold soldering defect on PCBA. thanks SC
Used SMT Equipment | Soldering - Reflow
The SMRO-4000 Scirocco Reflow oven has been developed for reflow soldering of Hybrid boards, SMT boards and Curing Glue or thin film pastes. The machine is developed for medium to large series of assembly. The Scirocco is based on hot air convection.
Used SMT Equipment | Soldering - Reflow
The SMRO-4000 Scirocco Reflow oven has been developed for reflow soldering of Hybrid boards, SMT boards and Curing Glue or thin film pastes. The machine is developed for medium to large series of assembly. The Scirocco is based on hot air convection.
Industry News | 2020-01-06 16:06:59.0
MIRTEC will premier its complete line of 3D AOI and SPI Inspection Systems in Booth #1900 at the 2020 IPC APEX EXPO. The premier technical conference and exhibition for the electronics manufacturing industry will take place Feb. 4-6, 2020 at the San Diego Convention Center.
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Technical Library | 2018-11-07 03:31:04.0
Generally speaking, there are not many cases of insufficient solder and solder short in BGA soldering, but it is not impossible. Here we discuss some elements may cause it
Technical Library | 2019-11-12 02:09:22.0
Thermal shock test chamber can be used for testing the chemical change or physical damage on composite materials caused by the thermal expansion and contraction of the sample in the shortest time,which is subjected to extremely and continuous high and low temperature environment.so how to check the temperature recovery time of this chamber? Normally we take following steps to inspect the temepratuire recovering time: 1.Install the temperature sensor at the specified position, and adjust the temperature controller of hot zone and cold zone to the required nominal temperature respectively. 2.The temperature increases and reduces respectively,30min after temperature in two zones reach stable status,record temperature value of the measuring point,pls set the temperature value of two zones to be required nominal temperature. 3.The temperature shock test chamber automatically places the inspected load into theh ot zone,select the corresponding retention time according to regulated standard. 4.Set the transfer time,then the inspection load is transferred from hot zone to cold zone, and the temperature of the measuring point is observed and recorded, and then the reverse conversion of the load from cold zone to hot zone is carried out according to the same method, and the temperature of the measuring point is observed and recorded. www.climatechambers.com
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
Welcome to this Defect of the Month video on monitoring flux application for wave and selective, this series of videos were produced for and featured as part of the NPL/IPC video library and examples are taken from the NPL Defect Database. Over the l
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Wed Dec 06 00:00:00 EST 2017 - Wed Dec 13 00:00:00 EST 2017 | Rolling Meadows, Illinois USA
X-Ray of PCBs Webtorial
Events Calendar | Thu Aug 23 00:00:00 EDT 2018 - Thu Aug 23 00:00:00 EDT 2018 | ,
Strain Gauge Data Can Be Misleading | Predicting Strain Levels Caused by Mounting PCBs in Housing Using the ICT Analysis Feature of Sherlock
SMTnet Express, May 9, 2019, Subscribers: 31,902, Companies: 10,760, Users: 26,083 Cold Ball Pull Test Efficiency for the PCB Pad Cratering Validation with the Ultra Low Loss Dielectric Material Credits: iNEMI (International Electronics
Heller Industries Inc. | https://hellerindustries.com/parts/800531/
800531 - Altered Cold Plate Phone 1-973-377-6800 Company About News Events New Equipment Convection Reflow Ovens Reflow Oven MK7 -New
Surface Mount Technology Association (SMTA) | https://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=5246
. On the basis of the volume change associated with the polymorphic transformation it was hypothesized that in the constrained conditions of a solder joint the stresses generated could cause the
.png)
