Industry Directory | Manufacturer
Global Designer & manufacturer of advanced electronic components, modules, systems & contract assemb
Machine vision uses image capture and analysis to automate tasks such as inspection, gauging, and counting, in addition to reading barcodes and optical characters (OCR). While human inspectors can visually inspect parts to judge the quality of workma
Electronics Forum | Fri Apr 11 11:26:09 EDT 2003 | Brian W.
Cracked capacitors usually are not found at ICT. Unless the cap is completely cracked, the capacitance may not change much, and the usual failure mode is a leakage current. This is usually only seen in ESS type testing, when temperature and humidit
Electronics Forum | Thu Sep 11 15:23:31 EDT 2003 | Peter L.
I have come across a rash of failed assemblies that have 0805 capacitors and resistors, bottom side glued, wave soldered and washed. Trouble shooter reported touching up the solder joints on a few areas and the boards would pass test. I had a look a
Used SMT Equipment | SMT Equipment
Product Name:Panasoinc high speed chip mounter NPM Product number: NPM1 Detailed product introduction NPM multifunction machine, SMT machine, machine with function function function, check the dispensing machine, is a multifunctional equipment
Used SMT Equipment | SMT Equipment
Product Name:Panasoinc high speed chip mounter NPM Product number: NPM1 Detailed product introduction NPM multifunction machine, SMT machine, machine with function function function, check the dispensing machine, is a multifunctional equipment
Industry News | 2008-08-14 13:20:36.0
ROSEMONT, IL � Industry-leading associations IPC and SMTA announce that Linda Woody will keynote Day 2 of the jointly sponsored High-Performance Electronics Cleaning Symposium to be held at Crowne Plaza Chicago O'Hare in Rosemont, IL on October 28-29, 2008.
Industry News | 2012-05-04 09:21:15.0
As printed boards evolve and chip speeds increase, the use of microwave technology in commercial applications, such as cell phone towers and in military products, is expanding.
Parts & Supplies | Assembly Accessories
Grease oil MGREAS400G0 OIL FILTER ELEMENT AFM30P-060S Oil Seal (TCV305011 ) AP1709A Oil Seal ( SC224211 ) AC1148A Metal foil low resistance chip resistors KRL2012E-C-R010-F-T1 Polyurethane coil tube UC-04-25
Parts & Supplies | Pick and Place/Feeders
> www.greensmt.com JUKI E9572729CA0 LA (L) CABLE ASM. SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95737290A0 MTC I/F(L) CABLE ASM. www.greensmt.com JUKI E95738550A0 DISPESE SV ASM SHENZHEN GREEN TECHNOLOGY CO.,LTD JUKI E95747210A0 BAD MARK SENSOR CAB
Technical Library | 2022-09-25 20:03:37.0
Cracking remains the major reason of failures in multilayer ceramic capacitors (MLCCs) used in space electronics. Due to a tight quality control of space-grade components, the probability that as manufactured capacitors have cracks is relatively low, and cracking is often occurs during assembly, handling and the following testing of the systems. Majority of capacitors with cracks are revealed during the integration and testing period, but although extremely rarely, defective parts remain undetected and result in failures during the mission. Manual soldering and rework that are often used during low volume production of circuit boards for space aggravate this situation. Although failures of MLCCs are often attributed to the post-manufacturing stresses, in many cases they are due to a combination of certain deviations in the manufacturing processes that result in hidden defects in the parts and excessive stresses during assembly and use. This report gives an overview of design, manufacturing and testing processes of MLCCs focusing on elements related to cracking problems. The existing and new screening and qualification procedures and techniques are briefly described and assessed by their effectiveness in revealing cracks. The capability of different test methods to simulate stresses resulting in cracking, mechanisms of failures in capacitors with cracks, and possible methods of selecting capacitors the most robust to manual soldering stresses are discussed.
Technical Library | 2023-11-27 18:29:45.0
This paper examines the modeling of viscoplastic solder behavior in the vicinity of interfacial cracking for flip chip semiconductor packages. Of particular interest is the relationship between viscoplastic deformation in the solder bumps and any possible interface cracking between the epoxy underfill layer and the silicon die. A 3-D finite element code, developed specifically for the study of interfacial fracture problems, was modified to study how viscoplastic solder material properties would affect fracture parameters such as strain energy release rate and phase angle for nearby interfacial cracks. Simplified two-layer periodic symmetry models were developed to investigate these interactions. Comparison of flip chip results using different solder material models showed that viscoplastic models yielded lower stress and fracture parameters than time independent elastic-plastic simulations. It was also found that adding second level attachment greatly increases the magnitude of the solder strain and fracture parameters. As expected, the viscoplastic and temperature dependent elastic-plastic results exhibited greater similarity to each other than results based solely on linear elastic properties. !DOI: 10.1115/1.1649242"
Higher, faster, further! And also bigger: Ersa HR 600 XL – the ultimate solution for professional big board rework up to 24 x 24 inches. See the capabilities and flexibility of this exciting machine. More about HR 600 XL ? https://big-board-rework.de
This is the first in a series of 10-minute videos to introduce new users to the basics of machine vision technology. In this video, users will learn what machine vision is, how it is used in factory automation, and its four most common applications.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Career Center | binan city, Laguna Philippines | Engineering,Maintenance,Technical Support
6.5 Years Experience in Semiconductor Industry Specializing in Dispensing process and Equipment. 5.0 Years of Experience in Field Service Engineering. Machine Commissioning / Customer support 24 / 7, Technical Support for Customer machine and process
KingFei SMT Tech | http://www.smtspare-parts.com/sale-12894127-metal-hook-spring-smt-feeder-parts-e1213706000-e1213-706-00-for-32mm-feeder.html
R E7904725000 PWB COVER E7911725000 EJECTER UNIT E79117250A0 EJECTER UNIT E79167250A0 FILTER E7917725000 FILTER ELEMENT E7918725000 FILTER ELEMENT E8001705J00 15 INCH LIQUID CRYSTAL MONITOR E80026700A0 I/F PWB ASM E80026710A0 I/F PWB ASM E8004705J00
KD Electronics Ltd. | http://www.kundasmt.com/?A-Equipment-Accessories/6006.html
Al T5/Z70 00317789-01 BUILT-IN ELEMENT LEL 71001A 00317792-01 BALL BEARING HOUSING 00317856-02 FRICTION BLOCK HOLDER 00317859-04 FRICTION BLOCK 00317861-03 Federblech 00317868-01 COMPRESSION SPRING 0,8*8,8