Welcome to the next generation in PWB test solutions. We combine an exceptional team of technology and applications experts with HIOKI's industry-leading systems to enhance your reliability and to speed up your product development process.
Industry Directory | Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Media / Publisher / Online Resource
All Through-hole & SMT PC Board Assembly equipments,Reflow and wavesoldering equipments,Humiseal conformal coating,SCH Technologies conformal coating equipments,Kyzen Cleaning solutions,Metronelec Solderability tester,Curing oven
New Equipment | Wave Soldering
Wave solder finger L type 7-c450126 Vitronics Soltec Delta 6622CC TITANIUM Grade 1 Commercial pure titanium Chemical composition (weight %) (Maximum values unless range is shown) O N C
New Equipment | Wave Soldering
Wave solder finger V type 7-c450001 Vitronics Soltec Delta 6622CC TITANIUM Grade 1 Commercial pure titanium Chemical composition (weight %) (Maximum values unless range is shown) O N C
Electronics Forum | Tue Sep 14 06:00:27 EDT 2004 | sc
dear, appreciate the sharing of experience on detection tools of cold soldering defect on PCBA. thanks SC
Electronics Forum | Tue Sep 14 06:00:31 EDT 2004 | sc
dear, appreciate the sharing of experience on detection tools of cold soldering defect on PCBA. thanks SC
Used SMT Equipment | Semiconductor & Solar
Bondtester by DAGE, in good condition. DAGE Series 4000 Bondtester product information. The 4000 bondtester is multipurpose, capable of performing all pull and shear applications. The 4000 bondtester can be configured as a simple bond wire pull
Used SMT Equipment | Soldering - Reflow
The SMRO-4000 Scirocco Reflow oven has been developed for reflow soldering of Hybrid boards, SMT boards and Curing Glue or thin film pastes. The machine is developed for medium to large series of assembly. The Scirocco is based on hot air convection.
Industry News | 2003-06-10 08:16:44.0
The following text describes the application of NWA Quality Analyst to quality control in the assembly of electronic components.
Industry News | 2009-02-03 13:34:04.0
New PCB Rework, Repair, Fabrication Training & Consulting Services.
Parts & Supplies | Component Packaging
Cold Forging, Sport training equipments, Soldering tools, metal forming
Technical Library | 2020-12-07 15:26:06.0
Temperature cycling testing is a method of accelerated life testing done to PCCs that are exposed to normal operation temperature variations over its lifetime. During the testing, intermittent "open" failures can first occur at the hot and cold extremes of the test, exposing weaknesses in the design and assembly. A poor/weak solder joint fatigues, a via trace or barrel cracks, loose connections or a component fails all causing an intermittent open. When not at extreme temperatures, the PCC assembly relaxes, the "open" closes creating electrical connectivity. If you are monitoring the PCC under test in-situ you will know that an intermittent failure has occurred, and the test could be stopped for inspection. If in-situ monitoring was not implemented, you would not know if there were intermittent failures or not. The PCC gets powered up and works fine at room temperature.
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
Lyra Reflow Oven is a soft soldering that realizes the mechanical and electrical connection between the solder ends of surface mount components or the pins and the printed board pads by remelting the solder paste pre-distributed on the printed board
During use solder builds up in the cavity in cold bump pull (CBP) jaws. This reduces their grip efficiency and affects the quality of your measurements. Cleaning the cavities is very difficult and small ball cavities can be damaged easily. XYZTEC ha
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Thu Aug 23 00:00:00 EDT 2018 - Thu Aug 23 00:00:00 EDT 2018 | ,
Strain Gauge Data Can Be Misleading | Predicting Strain Levels Caused by Mounting PCBs in Housing Using the ICT Analysis Feature of Sherlock
Career Center | Oakville, Ontario Canada | Production
Technicians / Technologists To help us continue setting the pace in a rapidly changing manufacturing environment, we need people to operate state of the art manufacturing equipment, perform failure analysis and quality inspection on a wide variety o
Career Center | Oakville, Ontario Canada | Engineering,Production,Quality Control
Technicians / Technologists To help us continue setting the pace in a rapidly changing manufacturing environment, we need people to operate state of the art manufacturing equipment, perform failure analysis and quality inspection on a wide variety
Career Center | la jolla, California USA | Engineering
More than 18 years experience in AOI. Refer to my resume for more details.
SMTnet Express, May 9, 2019, Subscribers: 31,902, Companies: 10,760, Users: 26,083 Cold Ball Pull Test Efficiency for the PCB Pad Cratering Validation with the Ultra Low Loss Dielectric Material Credits: iNEMI (International Electronics
.png)