Industry Directory | Consultant / Service Provider / Distributor / Equipment Dealer / Broker / Auctions / Manufacturer / Manufacturer's Representative
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
Industry Directory | Manufacturer
DONGGUAN KINGSUN AUTOMATION TECHNOLOGY CO.,LTD is a company which mainly provide used and new SMT parts, provide repair SMT key parts service,new/used SMT machine trading,SMT consumables and Peripherals equipment,Clean room, ESD..
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
New Equipment | Solder Paste Stencils
Eliminate hours of solder mask damage repair time for bga sites while improving rework yield. Are you frustrated by the time it takes to repair mask damage underneath the BGA during the rework process? Are you squeezed for space on the PCB in an
Electronics Forum | Wed Jun 30 10:37:11 EDT 1999 | Boca
We are wave soldering some fabs with a lot of unmasked trace area along the edges. The trace area is solid copper covered with tin / lead, no masking, no components along the edges, same on solder side and component side (goofy board design). Inste
Electronics Forum | Wed Jun 30 12:14:40 EDT 1999 | John Thorup
| | We are wave soldering some fabs with a lot of unmasked trace area along the edges. The trace area is solid copper covered with tin / lead, no masking, no components along the edges, same on solder side and component side (goofy board design). I
Used SMT Equipment | Soldering - Wave
Options: (1) IR-preheating, bottom side segmented pin/chain and roller conveyor for versaflow with double soldering module programmable conveyor width adjust (4) convection preheating top side automatic solder wire feeder, solder
Used SMT Equipment | Soldering Equipment/Fluxes
Solder Wave by SEHO, in good condition. SEHO GoWave 1030 product information. Usable soldering width max. 340 mm [13.39”] Pass-through height (measured from bottom edge of PCB) 100 mm [3.94”] PCB / solder mask dimensions l x w max. 410 x 340 m
Industry News | 2016-12-09 23:33:42.0
GPD Global offers advanced dispense pump technologies to upgrade your existing platform and take advantage of existing capital equipment. Retrofit your system with innovative dispensing technology for excellent dispense control and repeatability.
Industry News | 2016-07-16 13:32:29.0
Advanced dispense technology is available for integration into your dispensing system. Continuously Volumetric, drip-and-drool free dispense technology can now be retrofitted into your dispense robot. GPD Global's Volumetric PCD pumps ensure the success of applications like underfill, LED encapsulation, solder mask, silicones, conductive ink, conformal coatings, and more. Improve your throughput and yields by retrofitting a Volumetric PCD Pump into your dispense system to simplify the dispense process.
.jpg)
Parts & Supplies | Assembly Accessories
12MM Calibration Tape .12MM Calibration Tape 20 Inch Folding Bike Ravel Case 20 Inch Folding Bike ravel Case 4*4.1200pcs/bag M0604 8MM Calibration Tape .8MM Calibration Tape 90 degree drive set 90 degree drive set A2E BGA Rework Station Temp Con
.jpg)
Parts & Supplies | Pick and Place/Feeders
KHY-M7AC0-00 SCAN CAM. ASSY KGJ-M76A0-00X MASK LIGHT ASSY YVP KHY-M7AC0-000 SCAN CAM. ASSY YG12/YS12 KKD-M78C0-00 SCAN CAM. ASSY YS24 KHY-M7554-02 OF.LIGHT BRD.ASSY. 1 KHY-M7905-02 OF.SV.LIGHT BRD ASSY 1 KV7-M7165-00 SEAL DON'T TOUCH 1 KHY
Technical Library | 2019-05-29 01:47:22.0
1.Vias near SMD pads: Solder can flow into the via after melted. As a result cold joint will appear in the end. Check the picture below. 2.Vias on SMD pads: Solder can flow into the via more easier after melted. Check the picture below. 3.Via opening without soldermask covered. When workers solder TH parts by hand, soldering iron can touch vias sometime, then tiny amounts molten solder will stay on vias. This can lead to electrical short easily. We recommend you make all vias tenting (covered by solder mask) if it is possible.
PCBNPI-Professional PCB Fab/PCB Assembly Service Provider From China
http://www.gpd-global.com No drip no drool across a wide range of fluid viscosities (low-to-mid and low-to-high). No manual adjustment to compensate for pump variability. Truly Volumetric PCD Pumps for total control of dispensing fluids. Ability to
High Precision Dispensers - MAX Series (Non-Heated) Max Series is capable of a wide variety of dispense applications including MicroVolume, Solder Paste and Conductive Adhesive, Underfill, Surface Mount Adhesive, Dam and Fill, Encapsulations, LED En
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Events Calendar | Mon Apr 12 00:00:00 EDT 2021 - Mon Apr 12 00:00:00 EDT 2021 | ,
Europe Chapter Webinar: Tombstoning Components during Reflow Soldering - Causes & Cures
Events Calendar | Wed Jul 13 00:00:00 EDT 2022 - Wed Jul 13 00:00:00 EDT 2022 | Oshkosh, Wisconsin USA
Wisconsin Chapter: PCB Workshop and PCB Plant Tour
ASCEN Technology | https://www.ascen.ltd/face_mask_making_machine/681.html
Ultrasonic mask edge sealing machine for N95/FFP2 mask-PCB magazine loader,PCB turn conveyor,pcb conformal coating machine,PCB router,PCB depaneling machine,pcb buffer conveyor from ASCEN technology
PCB Libraries, Inc. | https://www.pcblibraries.com/Forum/smd-solder-mask-defined-and-nsmd-pads_topic1768.html
. The NSMD BGA pad stack is necessary for the Ball to fully collapse around the pad edge securing it to the PCB - The SMD (Solder Mask Defined) BGA pad stack prevents the Ball Collapse
