New Equipment | Education/Training
This specification covers qualification and performance of rigid PCBs including with or without plated-through holes, single-sided, double-sided, multilayer with or without blind/buried vias and metal core boards. It addresses final finish and surfac
New Equipment | Education/Training
IPC A-600H Acceptability of Electronic Assemblies. The IPC-A-600, "Acceptability of Printed Boards " is the most widely used published specification on printed wiring boards. This specification has set the standard for rigid printed boards in terms o
Electronics Forum | Fri Oct 08 09:43:27 EDT 2004 | davef
First, don't get too excited about the thermal capabilities of conductive epoxy. An epoxy like DuPont CB-100 increases the amount of heat conducted through the barrel, but many over estimate what it can do. Calculations show for a 0.020" drilled
Electronics Forum | Mon Nov 11 11:28:32 EST 2002 | davef
Sand is not a great conductor, compared to copper. Never heard of using the stuff on RF boards. Our board fabricator uses Dupont CP100, now CP101, [or something like that cuse who's going to check?] when plugging via on cheap boards. Your board fa
Industry News | 2011-01-12 17:48:44.0
GPD Global will highlight its Positive Cavity Displacement (PCD) Dispensing in Booth #6111 at the upcoming Automation and Technology West Expo (ATX), scheduled to take place February 8-10, 2011 at the Anaheim Convention Center in Anaheim, CA.
Industry News | 2011-02-04 01:47:14.0
GPD Global will highlight its Positive Cavity Displacement (PCD) Dispensing at the upcoming SMTA Dallas Expo & Tech Forum, scheduled to take place Tuesday, March 1, 2011 at the Richardson Civic Center in Richardson, TX.
Technical Library | 2015-12-23 16:57:27.0
The onset of copper barrel cracks is typically induced by the presence of manufacturing defects. In the absence of discernible manufacturing defects, the causes of copper barrel cracks in printed circuit board (PCB) plated through holes is not well understood. Accordingly, there is a need to determine what affects the onset of barrel cracks and then control those causes to mitigate their initiation.The objective of this research is to conduct a design of experiment (DOE) to determine if there is a relationship between PCB fabrication processes and the prevalence of fine barrel cracks. The test vehicle used will be a 16-layer epoxy-based PCB that has two different sized plated through holes as well as buried vias.
Technical Library | 2022-01-26 15:26:56.0
In this work an attempt is made to improve the fracture toughness and electrical conductivity of epoxy/glass fiber based laminates by the inclusion of carbon nanotube (CNT) fillers. The fiber orientation of the epoxy/ glass fiber (GF) fabric laminates was optimized based on estimation of mechanical properties. The carboxylic acid functionalized CNTs were incorporated into epoxy matrix by ultra-sonication method. The nano filled epoxy resin was used to prepare laminates with 30/45 GF fabric orientation. The CNT content was varied and its effect on the tensile properties was determined. The fracture toughness of multiphase composites was estimated using single edge notch bend (SENB) test. The presence of CNTs improved the fracture toughness by a crack bridging mechanism. The volume resistivity of multiphase composites was found to be superior to the conventional epoxy/CNT composite. The presence of glass fabric reduces the number of inter-tube contacts contributing to the reduction in volume resistivity.
This video describes the IPC A-600 training and certification program. The IPC A-600 specification is a set of acceptability specifications for printed circuit boards. These standards determine the acceptance and reject criteria for printed wiring bo
Whatsapp +86 134 2516 4065 PGB-1200 2 part epoxy silicone polyurethane auto glue potting machine epoxy resin dispensing machine AB compound pouring machine Model:PGB-1200 PGB-1200 system accurat
Training Courses | | | IPC-6012 Specialist (CIS)
The Certified IPC-6012 Specialist (CIS) training covers design, fabrication and inspection of rigid printed boards.
Training Courses | | | Other Courses
Other courses related to electronics manufacturing and assembly
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Career Center | Alta Loma, California | Engineering,Quality Control,Research and Development
Rigid and Flexible Printed Circuits Plating and Metal Finishing Operations Six Sigma Work Instruction Documentation Process Development Equipment Selection and Specification New Facility Startup Air, Water and Hazardous Waste Environmental Reporting
Influence of Nanoparticles, Low Melting Point (LMP) Fillers, and Conducting Polymers on Electrical, Mechanical, and Reliability Performance of Micro-Filled Conducting Adhesives for Z-Axis Interconnections. Influence of Nanoparticles, Low Melting
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/07/last-will-of-bga-void.pdf
: A total of 21 of 40 test vehicles had a void greater than 45% of solder ball diameter or 20% of ball area Solder crack path typically found at solder joint / BGA package interface Via in Pad (VIP
Surface Mount Technology Association (SMTA) | https://www.smta.org/store/book_store.cfm
and biomedical packaging, MEMS and wafer level chip scale packaging, and packaging materials such as lead-free solders, flip chip underfills, epoxy molding compounds, and conductive adhesives have all been updated with the latest developments in the