Industry Directory | Consultant / Service Provider / Manufacturer
Electronic manufacturing services - electronic design, development and manufacturing. Circuit board design, prototyping, FPGA services, signal integrity and simulation, pcb assembly. Factories in California USA and Malaysia.
Industry Directory | Manufacturer
Master Bond is a leading manufacturer of epoxy adhesives, sealants, coatings, potting and encapsulation compounds. Master Bond specializes in epoxies, silicones and uv curable polymer systems.
We are well versed in the following thermal application materials: Sil-Pad thermally conductive insulators Gap-Pad thermally conductive gap filling material Q-Pad thermal grease replacement film Bond-Ply thermally conductive adh
New Equipment | Assembly Services
S-Bond® solders are unique in their ability to provide a high performance thermal joint between these materials. S-Bond materials offer approximately 10 times the thermal conductivity of most thermal epoxies along with the ability to bond in air with
Electronics Forum | Mon Aug 27 15:06:29 EDT 2001 | davef
This otta push Wolfgang over the top ... Recommended reading G.G. Harman, Wire Bonding in Microelectronics : Materials, Processes, Reliability, and Yield, 2nd edition, McGraw-Hill Electronic Packaging and Interconnection Series, 1997. G.G. Harman, R
Electronics Forum | Sat Aug 15 07:56:16 EDT 1998 | Clyde F.
| | We need BGA rework station and x-ray inspector recently in urget case, Do you have any information to rework FPGA package and inspect them during processing. | Thx for any information | Best Regards, | Stoney Tsai PACE just came out with a new s
Industry News | 2010-12-07 14:53:07.0
GPD Global announces that its Positive Cavity Displacement (PCD) technology is proven with silver-filled electrically and thermally conductive adhesives.
Industry News | 2003-07-02 08:54:26.0
A novel unreinforced, thermally conductive, pressure sensitive adhesive tape delivers very high bond strength to low-energy surfaces.
Parts & Supplies | ESD Control Supplies
25KV Water Cooled Ceramic Capacitor Manufacturer Supply 25KV 5000pf 2000Kva Water Cool Ceramic capacitor High Frequency RF ceramic capacitor, Watercooled power RF capacitor, RF pot capacitor, water cool capacitor Specifications: Rated Voltage (V)
Parts & Supplies | Air / Vaccuum
Vishay Draloric TWX, TWXF 135285 Watercooled Power RF-Capacitors (External Cooling) Manufacturer Supply 20KV 5000pf 3000Kva (20KV 6000pf 3000Kva) Water Cool Ceramic capacitor TWX 12KVp to 20KVp TWXF 10KVp to 25KVp Rated Voltage (V): 10KV to 30KV
Technical Library | 2015-12-02 18:32:50.0
(Thermal Compression with Non-Conductive Paste Underfill) Method.The companies writing this paper have jointly developed Copper (Cu) Pillar micro-bump and TCNCP(Thermal Compression with Non-Conductive Paste) technology over the last two+ years. The Cu Pillar micro-bump and TCNCP is one of the platform technologies, which is essentially required for 2.5D/3D chip stacking as well as cost effective SFF (small form factor) package enablement.Although the baseline packaging process methodology for a normal pad pitch (i.e. inline 50μm) within smaller chip size (i.e. 100 mm2) has been established and are in use for HVM production, there are several challenges to be addressed for further development for commercialization of finer bump pitch with larger die (i.e. ≤50μm tri-tier bond pad with the die larger than 400mm2).This paper will address the key challenges of each field, such as the Cu trace design on a substrate for robust micro-joint reliability, TCNCP technology, and substrate technology (i.e. structure, surface finish). Technical recommendations based on the lessons learned from a series of process experimentation will be provided, as well. Finally, this technology has been used for the successful launching of the company FPGA products with SFF packaging technology.
Technical Library | 2010-06-03 22:23:03.0
Strategies for successful design and manufacture of microwave multilayer printed circuit boards. All aspects from pad registration, dimensional stability, impedance fluctuation, fusion bonding, thermal ageing, z-axis expansion, reliability, to Young's mod
General curing, die attach curing, underfill curing, film & tape bonding, wafer laminating.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
Events Calendar | Mon Apr 23 00:00:00 EDT 2018 - Thu Apr 26 00:00:00 EDT 2018 | Shanghai, China
SMTA China East Conference 2018
Events Calendar | Wed Mar 18 00:00:00 EDT 2020 - Wed Mar 18 00:00:00 EDT 2020 | College Park, Maryland USA
CALCE Reliability Science Symposium - Spring 2020
Career Center | Karachi, Pakistan | Engineering,Maintenance,Research and Development,Sales/Marketing,Technical Support
• Experienced in SMT Production, working on Siplace X Series-S and DEK-Micron Printer, on Siplace Pro and Siplace Explorer. • Having Strongly Skills of calibration of SMT machine, twin head, Multi star head, speed star head, gentry, Nozzles, feeders,
Successfully Designing FPGA-Based Systems SMTnet Express March 15, 2012, Subscribers: 25003, Members: Companies: 8826, Users: 32832 Successfully Designing FPGA-Based Systems by: Nagesh Gupta; Cadence Design Systems, Inc. Increases in field
.png)
