Industry Directory | Manufacturer
Thermally Managed ( up to 1000 W /m K thermal transfer rate ), CTE controlled, Very Rigid, Light Weight STABLCOR PCB / Substrate Technology
Industry Directory | Consultant / Service Provider
We specialize in thermal management consulting and R&D services for the electronics /telecommunications industry. We guarantee you personalized service, attention to detail, and the shortest turnaround time, world-wide.
The Henkel line of adhesives includes high temperature electrically conductive epoxy products for every customer’s needs. As the leader in thermal film formulation technology, Henkel has developed a wide variety of film materials for multiple appli
Introduction This oven is used for electron production and maintain of SMT technique. The product adopts the far-infrared heating components and excellent sense temperature materials. Through the precise control of the microcomputer, make the tempe
Electronics Forum | Thu Sep 02 16:52:31 EDT 1999 | Earl Moon
| | | Has anyone done or seen any studies done documenting what may be the affect of hardware such as screws in the parimeter vicinity of BGAs on a circuit board? | | | | | | What I'm really after is anything describing how close a screw/washer/nut
Electronics Forum | Wed Jun 23 13:56:56 EDT 1999 | Stan Frul
Hi Could anyone tell me where i can find information, in the literature or on the Web, concerning measurements of temperature distribution, expansion, stresses in the substrate and heat sink and on the interface between them, that is all the range of
Industry News | 2011-10-28 22:56:38.0
The SMTA released a summary today of the SMTA International Conference and Exhibition which attracted more than 1,000 attendees from 25 countries. The event took place October 16-20 at the Fort Worth Convention Center in Fort Worth, Texas.
Industry News | 2010-09-21 09:46:59.0
Dynamic Advance Allows Engineers to Instantaneously Map and Measure Pressure Distribution between Heat Sinks and Components in Real Time
Parts & Supplies | Pick and Place/Feeders
Supply&repair juki spare parts at l lower price: JUKI 710(720) CARRY UNIT E86127150B0 JUKI 710(720) CPU CARD E8601715AA0 JUKI 730(740) CARRY BOARD E86067210A0 JUKI 730(740) DC SERVO DRIVER E86037210A0 JUKI 750(760) AC SERVO CARD E86027210A0
Parts & Supplies | Assembly Accessories
JUKI 2060 Vacuum Ejetor PN 40001266 V8X-AG-0.3B-JU We are Supply SMT Pick and Place Equipment spare parts(Smt nozzle, Smt Cylinder, Smt Valve, Smt Sensor, Smt Feeder, Smt CPU Board, Smt Laser, Smt driver, Smt ejector……) for Yamaha, JUKI, FUJI ,Pan
Technical Library | 2017-11-15 22:49:14.0
While a significant level of voiding can be tolerated in solder joints where electrical conductivity is the main requirement, voiding at any level severely compromises thermal conductivity. For example, in LED lighting modules effective conduction of heat through the 1st level die attach to the substrate and then through the 2nd level attach to the heat sink is critical to performance so that voiding in the solder joints at both levels must be minimized. (...) In this paper, the authors will review the factors that influence the incidence of voids in small and large area solder joints that simulate, respectively, the 1st and 2nd level joints in LED modules and discuss mitigation strategies appropriate to each level. They will also report the results of a study on the effect on the incidence of voids of flux medium formulation and the optimization of the thermal profile to ensure that most of the volatiles are released early in the reflow process.
Technical Library | 2020-10-14 14:33:36.0
Epoxy based adhesives are prevalent interface materials for all levels of electronic packaging. One reason for their widespread success is their ability to accept fillers. Fillers allow the adhesive formulator to tailor the electrical and thermal properties of a given epoxy. Silver flake allow the adhesive to be both electrically conductive and thermally conductive. For potting applications, heat sinking, and general encapsulation where high electrical isolation is required, aluminum oxide has been the filler of choice. Today, advanced Boron Nitride filled epoxies challenge alternative thermal interface materials like silicones, greases, tapes, or pads. The paper discusses key attributes for designing and formulating advanced thermally conductive epoxies. Comparisons to other common fillers used in packaging are made. The filler size, shape and distribution, as well as concentration in the resin, will determine the adhesive viscosity and rheology. Correlation's between Thermal Resistance calculations and adhesive viscosity are made. Examples are shown that determination of thermal conductivity values in "bulk" form, do not translate into actual package thermal resistance. Four commercially available thermally conductive adhesives were obtained for the study. Adhesives were screened by shear strength measurements, Thermal Cycling ( -55 °C to 125 °C ) Resistance, and damp heat ( 85 °C / 85 %RH ) resistance. The results indicate that low modulus Boron Nitride filled epoxies are superior in formulation and design. Careful selection of stress relief agents, filler morphology, and concentration levels are critical choices the skilled formulator must make. The advantages and limitations of each are discussed and demonstrated.
ACI Technologies Inc. (ACI) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for The Department of Defense and industry. This video provides an overview of our commercial service
ASSCON’s vacuum soldering process combines the average of the vapor-phase with the vaccum process. The vaccum module consists of the evacuation unit mounted in the process chamber where it is secured with quick-locks for fast and easy removal f
Career Center | Murphy, North Carolina USA | Engineering
We are seeking a qualified and experienced senior design engineer to join our team. The best candidate will use both mechanical and electrical engineering skills to design innovative power supplies that are highly efficient, rugged, and have high rel
Career Center | Rochester, New York USA | Engineering
Our high tech client located in the Western NY State area offers you the following challenge. Complete mechanical design responsibility from specification to the manufacturing process. We seek a candidate that has the following experience: Design
Career Center | Riyadh 11623, Philippines | Engineering,Maintenance,Production
PROFESSIONAL EXPERIENCE: Connected in the field of manufacturing/electronics industry experienced in the line, Through Hole and Surface Mount Technology, worked on various Fuji Machines Universal model, such as: CP 643E chip shooter QP 242E chip mou
Imagineering, Inc. | https://www.pcbnet.com/blog/high-temperature-pcb-considerations-for-high-heat-applications/
. However, some debate exists as to whether heat spreading in a thicker copper layout lowers the total thermal resistance. The use of thermal adhesives can eliminate the need for mechanical fasteners like clips or screws, and can help reduce thermally conductive silicon insulators or gap fillers that isolate a device from a heat sink
ORION Industries | http://orionindustries.com/pdfs/gappad.pdf
, or other type of heat spreader. l Between CPU and Heat Spreader l Between a semiconductor and heat sink Property Typical Value Method Mechanical Thickness .020" to